LED vs CCFL 30-pin cables?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • spleenharvester
    Badcaps Veteran
    • Mar 2010
    • 902
    • UK
    #1

    LED vs CCFL 30-pin cables?

    Hey guys, for an all-in-one PC mod I'm doing I'd like to wire an LVDS cable from a small 30-pin LED laptop motherboard to a monitor, with an M190A1 CCFL panel.

    The panel's CCFLs will be powered by the monitor's PSU, I just need the data input from the LVDS cable.

    Is it as simple as just disconnecting a few LED power sources on the connector or is it a completely different beast?

    Cheers!
    Last edited by spleenharvester; 08-07-2013, 06:22 PM.
    Dell E7450 | i5-5300U | 16GB DDR3 | 256GB SSD
    Tags: None
    • spidey
      climbs
      • Dec 2012
      • 644
      • Cyprus
      #2
      Re: LED vs CCFL 30-pin cables?

      yes it is simple, need to check schematics first, could you give the codes of both ccfl and led panels.
      Last edited by spidey; 08-08-2013, 01:29 AM.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • eccerr0r
          Sell or Shim Solar panels?
          by eccerr0r
          Well, due to my grid tie inverter not accepting high voltages, and the fact that the lions in my solar panels are 36V (72-cell) I think I need to stick with 72-cell.

          However I have a few smaller panels that are 36, 32, and two 30-cell. The 36 and 32 together run at 75% efficiency (and subtract more with additional inefficiencies) when running in parallel with the 72-cell panels. The kicker is that the two 30s... generate 0% power when connected in parallel(!)

          So now what to do with these small panels?

          I could sell them...

          Or I could shim them....
          03-29-2025, 01:07 AM
        • NolesFan
          Samsung un82ru88000f - Boot loop sort of but can correct with taping of LVDS ribbon
          by NolesFan
          Hello all... TV started boot looping. Opened the back panel and tried to isolate the problem. Just PSB no boot loop. PSB and MB no boot loop. Plug in the LVDS from panel to MB and boot looping starts up. It doesnt matter of order that I plug the LVDS ribbons back in, only 1 and no boot loop but as soon as 2nd one plugs in boot looping. I then noticed a flicker on the screen when I was closing the clip on the harness to the LVDS. Shut the lights off so I can see better, and I noticed as i slowly close it, I will get a picture, but as soon as it clips in, I lose picture and booting happens. So I...
          2 Photos
          10-24-2024, 06:36 PM
        • mikey5791
          Help on Samsung Syncmaster T220 dead ccfl lamp
          by mikey5791
          Hi,

          This monitor previously is my main working monitor which i have been using for 8~9 years. Yesterday, when i switched on my pc from fresh to power on, the monitor is just black no display. I started dismantle to look inside the monitor power board but nothing looks suspicious or burnt. So i took my external ccfl inverter to try to power the monitor ccfl lamps which consisted of 2 lamps on upper part and 2 lamps on the lower part.

          Found out the upper ccfl lamp which is supposed to connect to cn304 on the power board did not light up. Then i installed a used working...
          10-18-2020, 03:17 AM
        • ttmi100x
          HANNSG Hi221 -- 2 secs to black feat. CCFL flicker & "burn" marks on power board
          by ttmi100x
          Greetings everyone,


          I have a HANNSG Hi221 monitor that exhibits two seconds to black issues (backlight goes off, display is still on as confirmed by shining a flashlight on it) with some additional oddities...


          The monitor failed on me with a standard "2 seconds to black" some time ago prompting me to initially replace most of the electrolytic capacitors (some of them were bulging/leaking).
          Things kinda sorta worked for a night, then the problem returned along with some flickering and "buzzing" noises.

          Upon closer inspection...
          "Burnt" resistor
          6 Photos
          07-31-2024, 06:36 PM
        • lpraderi
          Need help with HP15-fxxxxx Quanta U99/U92 LVDS <> eDP conversion.
          by lpraderi
          Hello , for some time I was studying Quanta U9x/8x schematics and the option to use both type of screen (LVDS 40 pin / eDP 30 pin).
          In some cases to use LVDS screen PCB use converter IC RTD2132/6
          Now I found an HP 15 F series U99 mainboard with RTD chip not populated and LVDS 40 pin lcd touch screen
          at the same time I have another HP 15 N series with Quanta U92 mainboard and RTD2136 with eDP 30 pin lcd screen (no touch).
          Maybe someone more experienced in the subject can clarify if is posible to change type of screen used with some resistors / bios options change.
          ...
          11-25-2023, 09:31 AM
        • Loading...
        • No more items.
        Working...