Windows 7 Experience Index System rating Test Appears Tough on Laptops

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Paul678
    Badcaps Veteran
    • Nov 2011
    • 402

    #1

    Windows 7 Experience Index System rating Test Appears Tough on Laptops

    That's what I'm noticing.

    I had one laptop that would give a blue screen of death
    during this test, but would work perfectly fine otherwise.

    And I just had another laptop, where I had just installed
    Windows 7 on a used IDE 60 Gig HD, and although it
    installed perfectly, the HD apparently was killed during the
    system test. Then the laptop couldn't see the drive at all,
    even with Knoppix.

    I suppose this is a good test, in that it weeds out the
    weaklings, or the components that are about to go
    bad.

    Anyone else notice this?
  • lucky13
    Badcaps Veteran
    • Aug 2007
    • 412

    #2
    Re: Windows 7 Experience Index System rating Test Appears Tough on Laptops

    Nope. Just your bad luck I suppose.

    That index isn't really stressful to your system like a real burn-in program can.

    Comment

    Related Topics

    Collapse

    • chth96
      How Can I test PWM DM0365R?
      by chth96
      Hello
      I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
      So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
      I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
      I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
      06-18-2025, 04:14 PM
    • khelane
      test active pfc power with lamp test
      by khelane
      Hello
      I have a big problem and that is that in some cases when repairing active pfc power supplies I cannot work with a test lamp. I can only get help with 5 volts standby and for starting and starting I have to work without a lamp and this way there is a possibility of parts exploding and other parts being added.
      Sometimes with a multimeter test the problems can be reduced to some extent, but I had several cases that had to be tested on and online and recently two varistors exploded. They had terrible resistance because the power supplies were over 800 watts.
      Is there a way...
      06-03-2025, 01:00 AM
    • chronic519
      Mats / mods: detected and repaired GPU fault. Cant seem to test after!
      by chronic519
      Hello.

      GPU came in, green lines. Spent lots of time using to get the Mats / mods drive working (found on youtube).
      Found issue with a RAM block
      Replaced, green lines gone.
      Trying to test again, assuming getting the false positive. Originally had over 1K on a single bank. Now getting tosses low between banks.
      Used a good card to test and same results low errors 32+.

      I am just search for some form of command to do a full test on the GPU.
      I just ran the mats command with my good GPU and passed after roughly 40 min.
      The repaired one, ran...
      05-20-2025, 07:56 PM
    • chth96
      Is it no harm to replace with capacitor without ripple current rating?
      by chth96
      When I tried to repair LG 29 inch CRT TV, I found that the ESR value of samyoung SMS capacitor(160v 2.2uf), which is very close to D1879 transistor, is 6 ohm.


      Judging from above ESR Meter Table,I think It is necessary to replace this sms capacitor.So I visited local electronics shop,and I purchased 160v 2.2uf rubycon YK capacitor.
      But when I browse through rubycon YK datasheet,I found that there is no ripple current rating for 160v 2.2uf specification. But On the contrary, I found 39 mA ripple current rating for 160v 2.2uf SMS capacitor.
      Rubycon YK DataSheet (b...
      04-19-2024, 05:19 AM
    • alltvrepairs
      Lg TCon test pins for screen test
      by alltvrepairs
      Hi,
      i have a 65 Panasonic TX-65HX710E using vestel 17MB170 main and Lg tcon.

      Few drops of water fell probably near COF and have no display. Tried removing tabs but no.part of display present as if tcon fuse open. However 12v is present and tcon can be felt warm enough that supplies are present. Backlight and sound ok.

      Anyone knows if this TCon 6870c-0805A has any special test pins for rgb test?

      Appreciate your help....
      06-13-2025, 06:33 AM
    • Loading...
    • No more items.
    Working...