Does anyone know where I can run a jumper wire to I believe its a power supply cable connector
Attached Files
-
-
Re: Ps4 saa-001 broken connector
Directly to the via (small circle) that your arrow is pointing to is what I would use to be honest. -
Re: Ps4 saa-001 broken connector
I trust my skills however this came to me with the connector broken and glue was placed on to attempt to fix it (a kid tried to clean it) exposing the copper and soldering to it is a gamble IMO but I'll do it anywayComment
-
Re: Ps4 saa-001 broken connector
maybe?
Open to suggestionsAttached FilesComment
-
-
Re: Ps4 saa-001 broken connector
Here, watch this video https://www.youtube.com/watch?v=Nba6HsO7RBU
Here is the via location on the other side of the board
Just search Google images for ps4motherboard saa-001Attached FilesLast edited by R_J; 06-22-2023, 05:35 PM.Comment
-
-
Re: Ps4 saa-001 broken connector
Thanks for the reply, I'll keep it in mind if I have to do this kind of repair again.
My ghetto fix actually worked
Comment
-
Hi everyone,
Sorry for the person who’s going to read all this !
I'm on a Nintendo Switch Lite, motherboard HDH-CPU-02.
While replacing the left joystick, I had to remove the motherboard to access the connector underneath. When I lifted the LCD connector latch, it broke (the plastic had become brittle over time), so I replaced the entire connector.
During the desoldering of the LCD connector using hot air, three small components located just below the connector (likely 0402 capacitors) came off and remained stuck to the bottom of the... -
Hello everyone,
Inside the console there is a small circuit board (see photo) that contains the main power switch, the one on the front.
This circuit board connects to a 10-pin flat cable called NEXUS that terminates on the motherboard.
This NEXUS connector broke.
Can anyone tell me, while waiting for a replacement, if it's possible to turn on the Xbox by disconnecting this circuit board and making some modifications (like adding a small power button) on the motherboard?
The Xbox has a power supply that provides 12 volts on all outputs, so the power... -
Hi All -
I had replaced my ASUS 4090 Strix cooler with a waterblock and put the stock cooler on the shelf. Was moving it and snagged my sweater on the connector and pulled the wires out of the pins on the RGB connector. I tried to get them back on but its too small so I opened the stamped pins and tried to solder but its not a good repair and the wire broke on reinstallation.
Looking to replace the connector on the cable side and get pins to crimp onto a new cable. Bought random JST and such but nothing is correct. Can anyone help identify the connector and possibly matching... -
Hi guys,
i have a damaged keyboard connector on my older Toshiba Satellite M50-A laptop. I know there is LA-A481P motherboard. In attachment pictures there is a real looking connector and i also found a schematic to the connector. But i need help with finding a real electronic part to replace the damaged connector. e.g. on aliexpress (or different page).
It is 34pin connector and the length from pin n.1 to pin n.34 is 26mm. So it means a pitch length is 0.764 mm. I have seen connectors with 0.5mm , 0.7mm , 0.8mm and 1mm pitch length. But not with 0.75. Is it some special custom connector... -
Problem
This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
Comment