My bosch charger stopped working and i found this blown fuse inside
I was wondering which fuse i could use that radio shack might have
I was wondering which fuse i could use that radio shack might have
-
-
Re: 1.6AL 250V Fuse Alternative
You've got bigger problems than the fuse, like shorted power semis.
Hint- they don't die, they're "murdered.""pokemon go... to hell!"
EOL it...
Originally posted by shango066Originally posted by smashstuff30guilty,guilty,guilty,guilty!
guilty of being cheap-made!
-
Re: 1.6AL 250V Fuse Alternative
How did come to that conclusion
I thought fuses are used to prevent damage to critical componentsComment
-
Re: 1.6AL 250V Fuse Alternative
If the circuit is drawing too much current due to failed components then before putting in the new fuse and causes more damages you should at least check out the circuit first or you can take a chance and install a new fuse.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: 1.6AL 250V Fuse Alternative
No, the most critical (and expensive) components are there to protect fuses.
Sometimes a fuse will protect other parts that haven't blown, sometimes not.
Fuses are mostly there to try to stop everything going up in flames when really bad things happen.
Photos would be a good start
"Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
-David VanHornComment
-
Re: 1.6AL 250V Fuse Alternative
cant answer the question without knowing the physical size & shape anyway.Comment
-
I've got a Monitor that's not showing any video, and I found this blown Fuse. As you can see from the photos, the board location has T4AL / 250V. Any assistance is greatly appreciated. Thanks!...
-
Hello, I disassembled this dead camera, and found this WTF… Two fuses soldered one above the other !
I was pretty sure nobody touched it before, but that can't be from factory. There is flux, and capacitor is probably missing.
The other weird thing : the fuses are « G » fuse : (0.75A – 8V), seems very low. The original fuse should be « O » : (32V 2,5A).
There is « O » mark beside. All fuses have the same mark letter on main board. So, I can deduce it's a « O » fuse.
And this correspond to the issus I saw : when I plug the battery, I measure the voltage dropping... -
Hello everyone, how can you test a thermal fuse?
I don't have a sign of life as an ohm or diode
Thank you -
Another victim of planned obsolescence.
BOSCH battery charger from year 2018.
PCB
1 607 503 091-C
PCB4040 Rev0.4 CEM-1 1.6T 10Z
2016-04-19
Fuse blew with nice sound effects. Seems need to replace fuse and resistor. No schematic is available.
Not sure what have caused this will try to replace 400v cap, resistor and fuse.... -
Hi I wonder if anyone might be able to steer me in the right direction. I have this Samsung UE46ES8000 TV and it went bang during use. The main fuse on the PSU board is open. I've checked every diode/mosfet/transistor I can see and nothing appears to be short to cause the fuse to go. The DC output of the bridge rectifier is not short either. I've seen online that some of these models are known for having their PFC mosfet or other mosfets shorting and blowing the fuse but i'm not seeing that here. If anyone aware of these models having any issues to cause this? I'm reluctant to just replace the...
Comment