Re: Best ESR meter/What to look for
My capAnalyzer 88A can't measure any thing lower 104 - 0.1 microfarad
Best ESR meter/What to look for
Collapse
X
-
Re: Best ESR meter/What to look for
The all topic is enjoyable.
It represents the constant battle between different generations of people. LOLLeave a comment:
-
-
Re: Best ESR meter/What to look for
Polystyrene film capacitor 0,5uF/250v 0,5%
http://img844.*************/img844/7267/ar6m.gif
Leave a comment:
-
Leave a comment:
-
Re: Best ESR meter/What to look for
I have a MESR-100 v2 and I have had no problems with it at all. For a meter that costs a little over $50 I think it gives you the most bang for your buck. It actually works for testing ESR while the cap is in circut too. I know there are instances when in circut testing is totally impossible but for the most part it works great.Leave a comment:
-
Re: Best ESR meter/What to look for
ST5 use several technics ... Gold tweezers
And inside ... so maybe the range is ok ... but in the field.
I have ST5 and tested in many components ... is better, and compare to HP
Best regards,
NeuronLast edited by neuron; 12-24-2013, 08:02 AM.Leave a comment:
-
Re: Best ESR meter/What to look for
Leave a comment:
-
-
Re: Best ESR meter/What to look for
Smart Tweezers
RLC/ESR
http://www.rlc-esr.ru/index.php?opti...d=61&Itemid=57
130$Leave a comment:
-
Re: Best ESR meter/What to look for
So what? If it works, which ivtec say it does, than why bother to get a more expensive one on some list? It does not matter.Leave a comment:
-
Re: Best ESR meter/What to look for
About four years back I thought also that I own great tools, but none of them were listed in the accepting list of those calibration - verification centers.
If no one accept to verify your tool as healthy, then you better not buying it.Leave a comment:
-
Re: Best ESR meter/What to look for
I use this one and in conjunction with fluke 87 it's a great tool
http://www.ebay.com/itm/USED-WORKING...item417a378e68Leave a comment:
-
Re: Best ESR meter/What to look for
Leave a comment:
-
-
-
Re: Best ESR meter/What to look for
Leave a comment:
-
Re: Best ESR meter/What to look for
This reaction makes someone to gain the title of a Troll.
The hook of yours seek for some sort of emotional reaction in return which will help you to add more pointless reactions on this topic, and the game will go on...
Even a simple green apple it is aware that it must stay on the tree many months until to become mature for collection.
Therefore stay on your tree and do not come down before your worth something as mature apple.Leave a comment:
-
Re: Best ESR meter/What to look for
Can I ask something to Administrators of this forum?
This posts are moderate or ...?
Because this stupid!!!!!!!!!!!
Ahhhhhhhhhh When you finish the kindergarden ... okLeave a comment:
-
Related Topics
Collapse
-
by chth96I read EBOOK of Testing Electronic Component and found that
"In order to test the small blue resin coated ceramic disk capacitor which has 104 50v specification,it is possible to test this small ceramic capacitor by making use of analogue meter.
Set to times 10Kohm that has 12v output from the probe to check disorder of ceramic capacitor.
It is not uncommon that testing result of digital capacitance meter is okay,But It show shorted reading when you check it with analogue meter."
Is it really possible to test small ceramic disc capacitor with analogue...-
Channel: General Capacitor Questions & Issues
-
-
by sam_sam_samI have had with regular AA batteries that leak this meter is expensive new I already replaced the battery battery clips once and the same thing happened again and I am tried of so it is getting modified to accommodate lithium ion batteries that are the same size excluding the positive terminal and removing the battery clips I will have enough room for the BMS protection board
I going to put 3 lithium ion battery in parallel with the BMS protection board and a way to charge the battery externally and heat shrink the battery pack and use a JST connector so I easily remove the battery... -
by jorpecHi
I want to change the scale of an analog meter, to monitor the charge of an li-ion single cell, so the needle at the end would point 4.2 volts and the 0 on the meter would point 2.5 volts or so, i tried to add diodes or a zener in series with the meter but the changes of the ambient temperature also changes the voltage value on the meter
I wonder how i can accomplish this so the meter would be precise at any temperature ?
Thnaks -
by sam_sam_samAbout a month ago we had a transformer jumper wire that burned in two different places between two transformers caused over $200 thousand dollars worth of damage to VFD drives at least 10 of them and a memory card and quite a few power supply as well
Now we have most of the equipment that got damaged back up and running except a feeder that has issues and we are waiting for some parts for
Now we also have another piece of equipment that was blowing fuses on the 110 volt controller switch circuit with the āEā stops and one switching power (24 volt) supply and a transformer... -
Greetings, new guy here but always interested in the crazy universe of modding
We just finished construction of around 25 vacation houses, all inside the same private area.
Each house has 3phase power , and we bought an atlas MK10 meter for each house (25 meters total ! )
The metering on a per-house basis is done privately. Its not done by a utility company. The utility company will only charge us for the total consumption of all 25 houses together.
Id like to do a small modification on the firmware of our MK10 to make it easier identify each house's...05-20-2025, 09:09 AM - Loading...
- No more items.
Leave a comment: