The motor they came from is made by MOTOR SPECIALITY INC. model 3069 B2.
Announcement
Collapse
No announcement yet.
Do these motor brushes need replaced?
Collapse
X
-
Re: Do these motor brushes need replaced?
The rotor is hard to turn with the brushes removed? The brush still have a log way to go.
The motor bearings still have any lubricants?Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
Comment
-
Re: Do these motor brushes need replaced?
Either it uses the bushing or bearings, sounds like they are in bad shape.
Any pictures?Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
Comment
-
Re: Do these motor brushes need replaced?
Can you easily turn the rotor since the rotor is attached to the other motor end bell housing.
They are just Bronze sleeve bearing, cheap! Put a fill drop of oil on the shaft and try to slide the end bell up and down to loosen up.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
Comment
-
Re: Do these motor brushes need replaced?
Use http://www.amazon.com/3-IN-ONE-10045.../dp/B00065VGUC
http://www.amazon.com/Markal-79704-S...d_sbs_indust_7
apply it to the shaft and rotate the rotor, clean off any gunk taht comes off, then re-oil it. The end bell in the picture, just put a few drops in the hole.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
Comment
Comment