recent addition Philips PM6303

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • llonen
    Badcaps Veteran
    • Sep 2014
    • 495
    • hampshire
    #1

    recent addition Philips PM6303

    Recent addition to the test equipment line up, have been after one of these or similar for a long time. While the fluke test meter I have does capacitance it does not offer the range this does. Neither does it cover inductance and impedance etc.
    Attached Files
    Tags: None
    • sam_sam_sam
      Badcaps Legend
      • Jul 2011
      • 6064
      • USA
      #2
      Re: recent addition Philips PM6303

      How well does it work

        Comment

        • llonen
          Badcaps Veteran
          • Sep 2014
          • 495
          • hampshire
          #3
          Re: recent addition Philips PM6303

          Pretty well actually I was having trouble identifying some weird banded capacitors in a scope I'm currently working on, pulled a good one from the board and it nailed it at 100nf. I checked it against the replacements going in and it nailed them within the working tolerance. Need to try it on some known inductor's, one of the reasons for obtaining the unit. Got it very cheap on an auction after some research showing these to be very expensive pieces of test equipment. It will do in circuit testing but can be affected by other components so if getting a strange result best to lift one end of or remove the component.
          Last edited by llonen; 12-23-2019, 09:26 PM.

            Comment

            Previous template Next

            Related Topics

            Collapse
            • chth96
              How Can I test PWM DM0365R?
              by chth96
              Hello
              I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
              So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
              I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
              I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
              06-18-2025, 04:14 PM
            • khelane
              test active pfc power with lamp test
              by khelane
              Hello
              I have a big problem and that is that in some cases when repairing active pfc power supplies I cannot work with a test lamp. I can only get help with 5 volts standby and for starting and starting I have to work without a lamp and this way there is a possibility of parts exploding and other parts being added.
              Sometimes with a multimeter test the problems can be reduced to some extent, but I had several cases that had to be tested on and online and recently two varistors exploded. They had terrible resistance because the power supplies were over 800 watts.
              Is there a way...
              06-03-2025, 01:00 AM
            • chronic519
              Mats / mods: detected and repaired GPU fault. Cant seem to test after!
              by chronic519
              Hello.

              GPU came in, green lines. Spent lots of time using to get the Mats / mods drive working (found on youtube).
              Found issue with a RAM block
              Replaced, green lines gone.
              Trying to test again, assuming getting the false positive. Originally had over 1K on a single bank. Now getting tosses low between banks.
              Used a good card to test and same results low errors 32+.

              I am just search for some form of command to do a full test on the GPU.
              I just ran the mats command with my good GPU and passed after roughly 40 min.
              The repaired one, ran...
              05-20-2025, 07:56 PM
            • ahmedtou
              HOW CAN I UPDATE HL-DT-ST BD-RE GGW-H20N XA02
              by ahmedtou
              Hi everyone,
              help me please


              I have an HL-DT-ST BD-RE GGW-H20N with ROM version: XA02.



              When I tried to burn a 25GB Blu-ray disc using ImgBurn, I got an error.
              I will share all the details with you, including the disc information.



              Code:
              HL-DT-ST BD-RE  GGW-H20N XA02 (ATA)
Current Profile: BD-R

Disc Information:
Status: Empty
State of Last Session: Empty
Erasable: No
Free Sectors: 12,219,392
Free Space: 25,025,314,816 bytes
Free Time: 2715:27:17 (MM:SS:FF)
Next
              ...
              08-27-2025, 08:49 AM
            • alro7779
              Philips 32PFL4901/F8 BA4GF0F0102 2 Not getting standby led
              by alro7779
              Hello, guys!

              The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601...
              09-14-2025, 12:25 AM
            • Loading...
            • No more items.
            Working...