LG 55EC930V OLED - 3 Second Power No Display

[Dac12]

Please ignore this photo completely wrong ic sorry

[Dac12]

don't miss up with SoC soldering.. .. i wrote MB, not SoC... yours MiCOM firmware distributed because of playing with microswitch which had nothings to do.... try disconnect pin 6 of MICOM and try IN_STOP

But I'm confused Diah has advised to disconnect pin 6?

[Diah]

Here is micom ic3000, but the remote control will not work if you cut the track to the 6 pin

RC will remain to work... this is SOS rail... RC took from other rail the function

[Dac12]

Here is micom ic3000, but the remote control will not work if you cut the track to the 6 pin

I'm confused because Diah has advised to disconnect it

[Dac12]

RC will remain to work... this is SOS rail... RC took from other rail the function

Yes thank you I understand now. But last question of many how do we disconnect this pin 6?

[Diah]

Yes thank you I understand now. But last question of many how do we disconnect this pin 6?

just pull it up from circuit

[Dac12]

just pull it up from circuit

Lol you mean heat it up and pull leg up? Or can the sensor be soldered off?

[Diah]

use thin soldering head with flux,,, don't heat the chip in total

[lotas]

RC will remain to work... this is SOS rail... RC took from other rail the function

Ok, let's see how the remote will work after removing 6 pin. The ir sensor and keyboard (joystick) are connected to this micom.

[Davi.p]

"yours MiCOM firmware distributed because of playing with microswitch which had nothings to do..."

and this sounds as the same old attack to others, every now and then it would be pretty to see from this individual documentation at support of these funny stories.. i will not support Dac12 more because is a novice and trends to listen funny technicians.. good luck (especially when you'll have to reattach virus size pin to a chip with super glue... my god..

[Dac12]

"yours MiCOM firmware distributed because of playing with microswitch which had nothings to do..."

and this sounds as the same old attack to others, every now and then it would be pretty to see from this individual documentation at support of these funny stories.. i will not support Dac12 more because is a novice and trends to listen funny technicians.. good luck (especially when you'll have to reattach virus size pin to a chip with super glue... my god..

Please don't be offended, I admit i am a novice first time on a electronics board. What would you suggested?
I can't freeze screen ribbons as you suggested because I cant get access to them.

I rely and value all your opinions but as you can clearly see I am at a disadvantage due to no electrical background

[Diah]

Ok, let's see how the remote will work after removing 6 pin. The ir sensor and keyboard (joystick) are connected to this micom.

Lotas, SOS will but whole TV in lamm RC, Keyw´s and send PSu to shutdown , MICOM as guard beside sequences of the operation. we have here threat where we did deep inspecting on MICOM at same model.
BTW : you can see its IN SOS signal not out

Davi.p:
just say in clear words did you have OLED repaired ?? no more or less... dont act you know the issue and you will not said it to owner of this problem... this is child play... be adult as yours age. .

[Davi.p]

Sorry dAc12, i will enter back the discussion when the King of Oleds finishes his efforts, i do not accept more bickering, i never own an oled, but i'm free to explore oled threads, maybe in some one country is forbidden by law..

[lotas]

IR + KEY ---- MICOM

[Diah]

IR + KEY ---- MICOM

lotas ,,, you are expert.. look on the diagram pin in and out.... in u can take it out... out pins are funktion

[lotas]

Well, everything is correct, the IR sensor receives a signal from the remote control, and from this IR sensor the coding signal comes to the input 6 pin. MiCOM and MICOM gives the command to turn on the TV...

[Diah]

Well, everything is correct, the IR sensor receives a signal from the remote control, and from this IR sensor the coding signal comes to the input 6 pin. MiCOM and MICOM gives the command to turn on the TV...

plese stop- as i cant laugh any more..... search please my post over oled and u will finf the correct answer how we did prove it,

[lotas]

plese stop- as i cant laugh any more..... search please my post over oled and u will finf the correct answer how we did prove it,

Ok, OP cut 6 pin. on MICOM and give any command from the service remote control and we'll see the TV's reaction, and we'll all have a laugh at the same time.

[Dac12]

Ok, OP cut 6 pin. on MICOM and give any command from the service remote control and we'll see the TV's reaction, and we'll all have a laugh at the same time.

We will do just give a couple of days, it's to small to see.

[Dac12]

plese stop- as i cant laugh any more..... search please my post over oled and u will finf the correct answer how we did prove it,

I don't understand- do you think we should not cut pin 6?