1-second to black 22" LCD need guidance

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • stormy1777
    Senior Member
    • Oct 2015
    • 128
    • USA

    #1

    1-second to black 22" LCD need guidance

    Hi friends..

    The question up-front:

    Is it safe/OK to replace a ceramic capacitor marked "5J 3KV" (which I assume is a 5pF, with a 10J 3KV, which i assume is 10pF.. I know the general rule in Electrolytic capacitors that one can go higher on the Voltage, but not on the capacitance.. Wondering if that minor (double) change will result is some "hazard" when ceramic capacitor and high voltage is at play ?


    I've carefully reviewed this guide over past few days:

    https://www.badcaps.net/forum/showthread.php?t=10419

    this LCD TV display powers on the LCD for split second, then turns off. I've attempted many tests but need some guidance..

    1) The main board seems OK, disconnecting the driver (HV) board shows that it is consuming ~12W and delivers 12VDC on the wires going to the driver board.

    2) the backlights are all OK, tested with a dedicated external LCD/CCFL driver, and all 4 lights turn on, and stay solid for long time.

    3) Also tested with external, known to be good CCFL (see image), and we get a burst of light (power goes up to ~30-40W for that split second), then they go OFF...

    4) Originally, there were two 25V@220uF Electrolytic capacitors which APPEAR to be leaking, but i think it's just some GLUE. they test OK on ESR meter as well as dedicated capacitor meter. Anyways, replaced with 50V220uF since it had the SAME physical size, and the new 25V220uF I had were HALF the size, so decided it is safer to go with the 50V.. Same effect after replacing both of these.

    5) Before I venture into totally unknown territories (like these scary "inverters"), spotted two blue ceramic capacitors marked "5J 3KV", took them off circuit, one gave 4.6pF, other 5.4pF. Now I realize that is not telling much, esp. due to low values, but then I do not have a 5pF, wondering if it is safe/OK to replace with 10pF which is the closest I got on hand


    Otherwise, appreciate any other ideas on how to diagnose this issue... or maybe the only recourse is replace the whole driver/inverter board....?


    Thanks in advance,

    Stormy.
    Attached Files
  • Andrew F. Ali
    Badcaps Legend
    • Jan 2014
    • 2450
    • Trinidad & Tobago

    #2
    Re: 1-second to black 22" LCD need guidance

    If you have 2 of the 10pF caps you can make a 5pF cap by connecting the 2-10pF caps in series to produce a 5pF cap.

    Comment

    • budm
      Badcaps Legend
      • Feb 2010
      • 40746
      • USA

      #3
      Re: 1-second to black 22" LCD need guidance

      1) So did you replace those two lytics caps on the inverter board with low ESR type caps?
      2) 5J = 5pF, 10J = 10pF if they are bad they will show leakage resistance when tested with Ohm meter.
      3) Did you test the resistance of the High Voltage winding side of the inverter transformers?
      4) Did you verify that the Voltage feeding the inverter board (12 ~18VDC is typical) and the Control Voltages (BL-ON, DIM) stay present when the lights go off?
      Never stop learning
      Basic LCD TV and Monitor troubleshooting guides.
      http://www.badcaps.net/forum/showthr...956#post305956

      Voltage Regulator (LDO) testing:
      http://www.badcaps.net/forum/showthr...999#post300999

      Inverter testing using old CFL:
      http://www.badcaps.net/forum/showthr...er+testing+cfl

      Tear down pictures : Hit the ">" Show Albums and stories" on the left side
      http://s807.photobucket.com/user/budm/library/

      TV Factory reset codes listing:
      http://www.badcaps.net/forum/showthread.php?t=24809

      Comment

      • stormy1777
        Senior Member
        • Oct 2015
        • 128
        • USA

        #4
        Re: 1-second to black 22" LCD need guidance

        1) Yes, as shown, and explained in #4 they were replaced, with same effect of black after ~1sec.

        2) Based on reading such places: http://www.facstaff.bucknell.edu/esa...captester.html, understood that a DMM cannot find such leaks of high voltage, and i do not want to touch the board when it is fully energized... not sure how to test. DMM shows OL when sent in Ohm mode, so i think that is OK.

        3) no clue how to do that...

        4) have not, will do that shortly.

        For now, I'm tempted to go with the suggestion to string 2 10pF and see how that works out...

        Thanks for the support.

        Stormy.

        Comment

        • dick_barton
          Badcaps Legend
          • Aug 2015
          • 6642
          • Wales

          #5
          Re: 1-second to black 22" LCD need guidance

          What is the part number of U1 on the inverter board? Is the set still working when the baclights go off ie can you hear the sound and see a picture on the screen if you you a bright light and angle it?
          Last edited by dick_barton; 10-03-2018, 11:42 AM.
          Willing to help but I'm no expert.

          Comment

          • stormy1777
            Senior Member
            • Oct 2015
            • 128
            • USA

            #6
            Re: 1-second to black 22" LCD need guidance

            Update:

            1) replaced both 5pF with couple of 10pF, as shown in photos, however, same black screen comes...

            2) After black screen, the voltage on the ribbon that feeds the inverter board shows 12V (red to black) and 5VDC (red to white) (maybe that is similar to what was asked "BL-ON, DIM"?.. so I'm thinking it is something with that inverter board..

            3) could not get the part# of U1, will need to go out to sun maybe with better quality light...

            4) I don't have any TV signal to feed it, nor do i know if the speakers ever worked, it is used as a PC monitor, just the vision part. Did not manage to "see" with a small flashlight, i'll need to find a strong light source to attempt to see if screen is visible or not.. there is a GREEN light and that is ON (when monitor is OFF, the light iis RED).

            5) is there any "easy & manual method" to "drive the inverter board? it sounds like if one could provide the 12V+5V on the right wires, that board would not be able to tell the difference, and will just power on the monitor (assuming it is not defective)..

            otherwise not sure what else is within my scope/abilities to repair

            I've replaced all 4 capacitors on that driver board...not sure what else to try...

            Stormy.
            Attached Files
            Last edited by stormy1777; 10-03-2018, 03:00 PM.

            Comment

            • budm
              Badcaps Legend
              • Feb 2010
              • 40746
              • USA

              #7
              Re: 1-second to black 22" LCD need guidance

              https://www.badcaps.net/forum/attach...4&d=1538599623
              Von/off = BL-ON (typ. >2.5VDC = ON) Ref. to GND (Blak wire).
              Vbrit = Diming control, it may be DC 0 ~5VDC (5V = full brightness) or PWM type control signal, ref. to GND (Black wire).
              Last edited by budm; 10-03-2018, 04:02 PM.
              Never stop learning
              Basic LCD TV and Monitor troubleshooting guides.
              http://www.badcaps.net/forum/showthr...956#post305956

              Voltage Regulator (LDO) testing:
              http://www.badcaps.net/forum/showthr...999#post300999

              Inverter testing using old CFL:
              http://www.badcaps.net/forum/showthr...er+testing+cfl

              Tear down pictures : Hit the ">" Show Albums and stories" on the left side
              http://s807.photobucket.com/user/budm/library/

              TV Factory reset codes listing:
              http://www.badcaps.net/forum/showthread.php?t=24809

              Comment

              • stormy1777
                Senior Member
                • Oct 2015
                • 128
                • USA

                #8
                Re: 1-second to black 22" LCD need guidance

                OHH regarding the "vbrit/von/off/vcc" I think got it!! That maps to the 6 wires that drive the inverter board. OK, so, Tested again, here are some findings:

                1) Results are same when display is OFF (but energized, connected to power) and right AFTER the screen goes black, in both cases these are the numbers in relations to GND (black):

                vbrit 0VDC
                von/voff 90mV
                vcc 12.3VDC

                Maybe something is wrong with the "vbrit" ? or maybe von/voff is too low?? or both? funny almost sure i saw 5vdc the other day somewhere there, but cannot find it now.

                so maybe something on the MAIN board needs replacing? I'm all for replacing bad caps, just no clue which one there are so many and none look bad or burnt in any way

                I'll checked in-circuit (using ESR meter) many of the large caps, they appear OK...

                2) As for this:

                3) Did you test the resistance of the High Voltage winding side of the inverter transformers?
                I'm not sure how to test these beasts, they have 2 pins on one side, and 6 on the other.

                Here is what I did with DMM:

                2.1) Ohm meter, all 6 pins on each of the inverters all show up as "0ohm", so all are same point it seems?

                2.2) from any of the two pins to any of the other 6 pins within the same inverter, the reading is "OL" - so , no contact...

                2.3) Ohm reading between the two pins, in both inverters comes as: 0.93KOhm.

                Appreciate any leads on where to go/spend time next

                Thanks!!

                Stormy.

                Comment

                • budm
                  Badcaps Legend
                  • Feb 2010
                  • 40746
                  • USA

                  #9
                  Re: 1-second to black 22" LCD need guidance

                  Are the test done with the unit connected to running PC or with Video source connected?
                  It looks like the main board just stops sending the two needed command signals (BL-ON and Dim).
                  Never stop learning
                  Basic LCD TV and Monitor troubleshooting guides.
                  http://www.badcaps.net/forum/showthr...956#post305956

                  Voltage Regulator (LDO) testing:
                  http://www.badcaps.net/forum/showthr...999#post300999

                  Inverter testing using old CFL:
                  http://www.badcaps.net/forum/showthr...er+testing+cfl

                  Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                  http://s807.photobucket.com/user/budm/library/

                  TV Factory reset codes listing:
                  http://www.badcaps.net/forum/showthread.php?t=24809

                  Comment

                  • stormy1777
                    Senior Member
                    • Oct 2015
                    • 128
                    • USA

                    #10
                    Re: 1-second to black 22" LCD need guidance

                    just power, no video source.. I'm suspecting i would need to connect to some PC/laptop... ok, let me see if that changes anything, although it behaved in same way when it was on the PC, i.e. fade to black.. and the TIME seems to reduce, i.e. now it is less than 1 sec fade to black

                    Comment

                    • stormy1777
                      Senior Member
                      • Oct 2015
                      • 128
                      • USA

                      #11
                      Re: 1-second to black 22" LCD need guidance

                      Noticed it changed behavior a bit with the two 10pF capacitors, maybe connection was not great, after POWER off, the GREEN light would not stay, it turned to RED light, i.e. completely OFF, power consumption dropped to 2-3W..

                      so, put the original 5pF capacitors, and now after power off and GREEN light remains ON, with ~12W power draw, and the voltage values to inverter board are now (after screen is black, light is GREEN):

                      vbrit 0VDC
                      von/voff 4.8VDC
                      vcc 12.3VDC

                      these values appeared with or without Video Source (there is AV/TV button, so kept pressing it, but it did not seem to change anything).

                      I'll test/compare more thoroughly the bunch of capacitors, marked CD11C and CD263, found on main board...
                      Stormy.

                      Comment

                      • stormy1777
                        Senior Member
                        • Oct 2015
                        • 128
                        • USA

                        #12
                        Re: 1-second to black 22" LCD need guidance

                        Well, scanned the main board, could not find anything glaring, all diodes look clean, and low ESR.. then remembered some LED debug kit got while ago, in it was a small "driver board", connected it and:

                        1) it did not power the CCFL on the monitor, i think that is expected, those require HV..

                        2) it did deliver 12VDC on the output ports, put LED strips and it did power them up.. so , maybe the inverter board is bad after all...

                        I might order something and see

                        Thanks for the help.
                        Stormy.

                        Comment

                        • stormy1777
                          Senior Member
                          • Oct 2015
                          • 128
                          • USA

                          #13
                          Re: 1-second to black 22" LCD need guidance

                          sorry, here is the photo prior session timed out and did not upload the image.
                          Attached Files

                          Comment

                          • stormy1777
                            Senior Member
                            • Oct 2015
                            • 128
                            • USA

                            #14
                            Re: 1-second to black 22" LCD need guidance

                            Here is an update, with new photos.

                            Got a replacement Video inverter board in the mail, it looks good, and identical to original one, installed the new one, and same thing, 1-sec and it goes to BLACK (it does manage to print the LCD logo)...

                            Took a separate interter device, and all 4 CCFL harnesses produced bright light on the display, so i was driving each one separately, and they all turned on and stayed on for long time.. which means the lights are OK, the inverter board is probably OK, which leaves the main circuit board...

                            that one is rather large with many smaller capacitors, I have no clue which would cause this issue... and to replace them all, well, I'm not really set up for that...

                            was thinking to order a replacement board: M220EW01 from ebay and try my luck a second time, only thing is all these look much NEWER compared to this one, so might need to make some adjustments once it arrives..

                            anyways, just though to drop this update and possibly there will be another update at a later time..

                            Stormy.
                            Attached Files
                            Last edited by stormy1777; 10-30-2018, 11:06 AM. Reason: upload images

                            Comment

                            • stormy1777
                              Senior Member
                              • Oct 2015
                              • 128
                              • USA

                              #15
                              Re: 1-second to black 22" LCD need guidance

                              Happy ending to this thread... ended up ordering a really cheap KIT from "China", it is totally different even though seller promised it is the same model to the letter.

                              In any event, as you can see, nothing aside from the monitor ribbon/cable fit, different sizes plugs, etc. so speakers and controls are not working, but it's fine, there are external speakers anyways.. power is on front panel

                              Thanks for the help, it ended up being the main board that was defective!!!

                              Stormy.
                              Attached Files

                              Comment

                              Related Topics

                              Collapse

                              • osrex
                                LED DRIVER KEEPS DYING
                                by osrex
                                Hello, this is my first post and im just a beginner, so be easy on me guy. thanks



                                i have a LED chandeilier that switches colors from white to cool white to warm when toggling the switch, it has 24 LED arms, each arm is 30 CM length.



                                i have no datasheet at all for the LED lights, all i have is its length.



                                long story short, testing the chandelier on the ground, and it works fine for 1 - 2 - 6 hours, no problem.



                                as soon as i fix the chandelier to the ceiling and bury the driver inside the hub,...
                                05-05-2025, 03:36 PM
                              • howardc64
                                Vizio E55-F1 dark backlight zones. LED failure or Dimming Zone Driver?
                                by howardc64
                                Problem

                                Fixing a dimming zone TV with LEDs not lighting up. Dimming zone circuit introduces added variable to diagnose LED and/or Dimming Zone Driver board? Some 1/2 rows of LEDs appears to be out in active dimming zone off AND some brightness flickering with active dimming zone high while playing changing video



                                Model & Board Pics



                                Conflicting Spec

                                Vizio indicate this TV has 10 dimming zones. However, LED strips and Zoned light driver connector suggest 12

                                https://www.shopjimmy.com/vizio-gj-2k1...
                                10-10-2024, 01:16 PM
                              • charif
                                Audio Driver for Thomson P14C4BK128
                                by charif
                                Need Audio Driver for Thomson P14C4BK128 (Windows 10/11)

                                Hi everyone,

                                I'm looking for help finding the correct audio driver for my Thomson P14C4BK128 laptop.
                                The sound is not working properly, and I believe the audio driver is missing or not installed correctly.

                                Here are the details:
                                • Model: Thomson P14C4BK128
                                • Operating System: Windows 10 64-bit

                                If anyone has a working link to the driver or knows where I can download it, I'd really appreciate it.

                                Thanks in advance for your help!
                                04-30-2025, 05:41 PM
                              • bohaboha
                                how to install gl usb2.0 uvc camera device driver on windows 10
                                by bohaboha
                                Hello all am trying to reinstall my AMCAP Microscope on windows 10 but it is not working anymore. But the cam and the drivers are present in the Device Manager but there it saysWindows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39) the drivers is : gl usb2.0 uvc camera device driver and i also get this mesage: Windows found driver software for your device but encou​ntered an error.
                                but it is quite strange because it did work on this same OS for one week ago and even for sometimes ago on that same but now nix.
                                any help?
                                01-26-2025, 08:33 PM
                              • chth96
                                Is it possible to test small ceramic disc capacitor with analogue meter?
                                by chth96
                                I read EBOOK of Testing Electronic Component and found that

                                "In order to test the small blue resin coated ceramic disk capacitor which has 104 50v specification,it is possible to test this small ceramic capacitor by making use of analogue meter.
                                Set to times 10Kohm that has 12v output from the probe to check disorder of ceramic capacitor.
                                It is not uncommon that testing result of digital capacitance meter is okay,But It show shorted reading when you check it with analogue meter."

                                Is it really possible to test small ceramic disc capacitor with analogue...
                                03-09-2024, 10:03 PM
                              • Loading...
                              • No more items.
                              Working...