Announcement

Collapse
No announcement yet.

Panasonic TC-P50C2 6 Blink Code Problem

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Panasonic TC-P50C2 6 Blink Code Problem

    This Panasonic has me fairly stumped. The problem Once plugged in, and you go to turn the TV on. You hear what sounds like normal clicks of the power supply, and sounds like it wants to fire up but then you hear 1 more click and shuts down and you have a 6 Blink code.

    I have followed The trouble shooting guide below.

    https://archive.org/stream/Panasonic...e/n67/mode/2up

    After removing the SC 20 Ribbon Cable and C10 ribbon cable. I power up and get 8 Blink code. Which Suggest the SC board is bad. I pulled the board to see if I could find anything wrong, but nothing obvious, no IGBT or transistors shorted, no diodes shorted.

    Before I order a replacement. I was hoping if anyone had any testing suggestions.

    Board Part Number TXNSC1LNUU (TNPA5063) SC Board
    Tags: None
    #2
    Re: Panasonic TC-P50C2 6 Blink Code Problem

    I think these boards are not repairable...not too sure if they can be repaired. If you have deducted that these boards are bad. look for replacements off e-bay , shopjimmy and all the other places that sell electronic parts. Good luck.

    Comment

      #3
      Re: Panasonic TC-P50C2 6 Blink Code Problem

      It was not the SC board I ordered. I am having problems Locating the issue any help would be apprecaited or any ideas.

      Comment

        #4
        Re: Panasonic TC-P50C2 6 Blink Code Problem

        Help us helping you.
        Post pictures of your tv,one from the total lay out of boards,then one from each board.Take a good close up of the logic board,and of the connectors with legend of the power supply etc.
        Also,take voltage readings on the power board.Mainly the VS and VA for now. Repeat those readings with the y main and x main unplugged and report back.
        Note: Do NOT plug the y main and x main back in right away,first make sure the power supply drained proper.
        Proud owner of dozens of broken TV's and many,many,many boards.


        Our website and passion:http://hollenhundshepherds.com/

        Comment

          #5
          Re: Panasonic TC-P50C2 6 Blink Code Problem

          Originally posted by martino View Post
          Help us helping you.
          Post pictures of your tv,one from the total lay out of boards,then one from each board.Take a good close up of the logic board,and of the connectors with legend of the power supply etc.
          Also,take voltage readings on the power board.Mainly the VS and VA for now. Repeat those readings with the y main and x main unplugged and report back.
          Note: Do NOT plug the y main and x main back in right away,first make sure the power supply drained proper.
          Helping me lose the plot
          Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

          https://www.facebook.com/Telford-Tel...7894576335359/

          Comment

            #6
            Re: Panasonic TC-P50C2 6 Blink Code Problem

            I will Get pictures up today. And Voltages.

            But off the top of my head, I have replaced the Poower Supply with a working power Supply I had laying around, also I have reflowed the Bottom of both SC and SS Boards. Have tested Components on both. But I can still get voltages, And replaced the SC board it was cheap so just replaced it. Still no luck

            I am leaning Toward MainBoard.

            Comment

            Previous template Next
            Working...