Re: Eeprom dump thread!
micromax ad panasonic dump
micromax ad panasonic dump
-
Last edited by Rajnhl; 12-26-2018, 05:42 AM. -
Comment
-
Re: Eeprom dump thread!
anyone help me with toshiba 32p2305ze firmwareComment
-
Re: Eeprom dump thread!
hello bro I tried firmware of TOSHIBA 32P2305EV.
now led is on (before it was blank screen) language is not english but av picture is good i will try to change language and post result.
pls. if you can provide exact model it will be more help full.i will post 32p2305ev and tcon firmware tomorrow.Comment
-
Re: Eeprom dump thread!
toshiba 32p2305ze working perfectly by flashing 32p2305ev firmware.Comment
-
Re: Eeprom dump thread!
Hello Guys
Happy new year to all !
I am writing to you because of my TV SONY BRAVIA KD-49x8307C I have a problem with this model is totally bricked after last update.I have tried to reset it with usb flash drive and the right software provided by Sony but there is no luck.The problem is that when I hold Vol - and Power for 30 Sec. Tv is getting into recovery mode but does not want to download the update from the usb flash drive I have attempted many times...
I need a dump for thee EEPROM or NAND (eMMC) 16 Gb Ic.
NAND Ic is SK hynix H26M52103FMR , and eeprom :Winbond 25x40cling.
Thanks in advance !
AlexComment
-
Re: Eeprom dump thread!
Hi all, I'm looking for an Eeprom dump for a Digihome TV as follows.
Digihome.
Model - 48272SM FHD LED
Screen type - Vestel - VES480UNDS2DN01
Board number - 17MB95M
The fault on the TV is that it powers up with backlight on but has no picture.
P.S. I've been looking for a place like this with somewhere I can share my Eeprom dumps and will soon be uploading dumps too.
Thanks.Comment
-
Re: Eeprom dump thread!
Hi all,
I'm looking for an Eeprom dump for a PANASONIC TV as follows.
MARQUE : PANASONIC PLASMA
MODEL : TX-P50GT60E
Board number : TXN/A1ATVE or TNPH1043 1A TXN/A1ATVE
Thanks.Comment
-
Re: Eeprom dump thread!
Here is a good .bin for a Vizio E390-A1 Mainboard# TXCCB02K038
The Eeprom is at U409 Winbond 25Q64FVSIG or a Macronix MX25L6445E
This is a good .bin. It fixed my problem. The set would get stuck in standby and would not turn on or off.Comment
-
Re: Eeprom dump thread!
Hi, guys.
I have Hitachi 32HYT46U with the problem random switching. Turn on, can see Hitachi logo and turns off then. And the same again. I think that reprogramming of U10 would resolve this problem. If anyone, you guys, have a right bin file, please share with me.
Thank you in advance.Attached FilesComment
-
-
Re: Eeprom dump thread!
Main is: 17MB95M vestel
Main board: Vestel 17MB95M
Power board: Vestel 17IPS71
Panel: LC320EUJ-FFE2Attached FilesComment
-
-
Comment
-
Re: Eeprom dump thread!
MODEL: 32/173I-GB-4B-hbkup-eu
MODEL: b32fa173bk
PRODUCT CODE: BW32O173BBKPE421
MAINBOARD: T.MSD309.9b 10345
PANEL: LTA320AN12
TUNER: XDTT-6F1C/T1146Comment
-
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... -
Comment