Re: Another 60PV250 pic fault but different this time. Help greatly appreciated
No one has any clue??
No gurus??
No one has any clue??
No gurus??
-
-
Re: Another 60PV250 pic fault but different this time. Help greatly appreciated
All the menu does it change the times between sustain pulses, are all voltages like Vsc running at the correct spec to the panel ?Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: Another 60PV250 pic fault but different this time. Help greatly appreciated
Increasing the brightness probably just moves pixel data between sub fields affecting how each subfield is balanced.
This is a z-sustain fault regardless of what the voltages do, there is no one voltage that controls the brightness. In fact on most plasma TVs the voltages will stay steady under 90% of picture conditions, only changing when the scene gets significantly darker (as subfields are dropped because of lack of picture brightness) or significantly brighter (as subfields are stunted by the ABL control.)
Some older LG plasmas would turn off Vzbias when the picture went black as you don't need it for priming, only for full discharge. But not aware of any modern sets that do this, due to the delay in pumping Vzbias back up (enough to cause momentary maldischarge)Last edited by tom66; 09-17-2016, 05:23 PM.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another 60PV250 pic fault but different this time. Help greatly appreciated
Yes all voltages perfectly stable.
Im going to try changing the fet driver controller chips (8 pin) next. Since the zsus boards are not available anywhere.Comment
-
Re: Another 60PV250 pic fault but different this time. Help greatly appreciated
Put the oscilloscope on the outputs of both zsus fet driver schips.
One is show busy square wave.
Other is a flat line. Assuming the flat one is faulty.
Ordered a complete repair kit. Will post results later.Comment
-
Bit of a weird one here...I have this HP Envy which has an odd fault. Basically the power button doesn't turn the device on. However, immediately after a BIOS reset, it will turn on from battery once, and it'll continue to tun on from mains quite happily, first time every time for a few hours (but will not power on from battery at all). After a few hours, the button will become increasingly unresponsive again even with mains connected. I've replaced the battery, even though there were no signs of a battery problem, and the issue remains. From reading another post on here, the experts were... -
85” Hisense TV
Greetings,
Request for Technical Assessment – Faulty Hisense 85Q6NAU TV
Dear TV technicians of forum, I hope this message finds you well.
I am writing to seek assistance regarding my 85-inch Hisense Smart TV, model 85Q6NAU, which is currently experiencing a fault. The unit is approximately two years old, and I am not sure if it has a warranty.
I have attached a photo showing the issue for your reference. I would appreciate it if your experienced technician could kindly review the image and provide some insight... -
Hi guys, this is my first post on here so please be gentle.
I have this ASUS ROG SCAR 16 - G634J laptop that keeps on freezing intermittently, showing a red blinking battery light, resulting in a frozen screen, unresponsive keyboard, only a hard reset will bring it back on. I will say that due to the frequency of it happening now it is really hard to try to load up any monitoring software etc.
Now here is the thing, I have seen at least 5-6 posts around on reddit and ASUS's official forums with individuals all having this exact issue. My bet is that its something to do with... -
Hope someone can give me some suggestions on this because i'm at my wits end with it...
I have an Envy 13-BA1565na here with an Intel Core i7 i7-1165G7 CPU (board is a LA-J475P Rev 1.0) which has an intermittent power button issue. The power button is integrated into the keyboard, and I have ruled out the keyboard, BIOS and battery as being the issue.
Basically, on mains power, the power button works fairly well. The first time you come to it after leving it sitting (either on charge or not on charge), it might take 2 or 3 presses of the button, but then the laptop boots...07-12-2024, 03:03 AM -
Hi there,
First, I'm not sure it's the right section to post for this type of device, but could not think of something better.
Ok, so my son (a mechanic) bought a faulty Hofmann Geodyna 6300 wheel balancer (which appears to be mostly a re-branded Snap-on wheel balancer).
I'm looking for any resources (doc, manuals, schematics) that would be available for this device or anyone that would have any knowledge on this particular device (or its Snap-On equivalent).
I'm trying to diagnose the fault(s ?), but I can't find any schematic (appart from the...
Comment