Panasonic SC Board - BAD 30F131 IGBTs

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • kc8adu
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs


    [QUOTE=MICROTECHSERVICE;666665 he told me put them in( boiling water !!!)
    [/QUOTE]

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Yes I take your point especially regarding the Chinese components, though I thought the UK ones would have been ok. I will wait for the alternate parts to arrive. I have spent a lot of time reading various posts on here and am wondering whether I should replace the drivers (BD8693) and corresponding transistors (CPH5524). I looked at a schematic and it looks as though I would need to replace 3. The transistors can be bought through rs but I can't find a local supplier for the drivers, only Chinese suppliers. Do you know of a supplier and what's your opinion on replacing them. On a seperate post, a person had the same issue, all ok till he connected sc20 ribbon then bang. Replaced drivers and blown components and all good. I appreciate your feedback

    Leave a comment:


  • tw2005
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Why are you persisting with potentially crap parts. Keep it up if you want extra stuff to fix. My TV last about 3 boards in succession with fake parts blowing instantly on the 4th it blew open the P2 track for Vsus to the SC board which resulted in 7 blink once I got the board fixed properly..

    I think if sc20 is disconnected it gives 8 blinks,

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Update, checked the ribbon,sc20 connector. Re-powered and the sc board failed again.

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Thought I would fit the Chinese components to the sc boards and run some tests, whilst I wait for delivery from Rs components. No short found at sc2. No short found at q102 on the ss board. Fitted sc board and isolated both Su an sd boards. Fitted jumper, connected sc2 and sc20. Powered up, now showing 8 blinks. Checked s2 again. Open cct in one direction 320ohms in the other. Direct short between pin 3 on sc2 and ground and open between pin 1 and ground. Any Ideas?

    Leave a comment:


  • tw2005
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by Librian1969
    Just a further note, when the tv originally failed, I mentioned I heard a loud pop noise before it went into the 7 blink fault mode. I expected that I would see an obvious sign of a failed component, cap etc. Thoughts?
    They all go pop not that I get to experience that except when I get shit parts. Unless it is violent enough to blow the head off a transistor you won't see a thing.

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Just a further note, when the tv originally failed, I mentioned I heard a loud pop noise before it went into the 7 blink fault mode. I expected that I would see an obvious sign of a failed component, cap etc. Thoughts?

    Leave a comment:


  • tw2005
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    look like this

    Leave a comment:


  • tw2005
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by Librian1969
    Will do, will order them today and see how it goes. What method do you use for fitting to to the board? I have seen a number of recommendations from using solder paste and heat pencil to soldering iron on the tab till solder melts. Either method creates a lot of heat to the component. The legs are the easy part.
    If you can get the old ones off, you'll find putting these ones on an absolute piece of piss.

    I fully dewick the pads, dab of flux and you're in business as the tab draws so much less heat from the iron it's a breeze.

    If you have hot air you can use that to preheat the board a bit but I hand solder the transistors in.

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by dj01fad
    I found 25 pcs on a private near my town a few months ago, at 35euros for all of them, and bought them. I used them and all worked fine. Now I am out of stock, and still waiting for the package from china (100 pcs). will see if they are ok. (I am a little worried)

    meanwhile, I received 6pcs 30f131 from panasonic service, and repaired a sn board from a P42GW30, and it is working perfect (non stop since yesterday). the funny thing is that they still have these on stock! i can take a some photos with the packaging from panasonic, and the 30f131 piece if you want. the tv is still open.
    OK thanks. If you have already reassembled he TV that would be good.

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by tw2005
    Ok, normally the diodes survive.

    You could assume the parts may have been bad in which case you could order 10 FGD4536 from RS components and use them for q401,402,403,421,422,423 .

    they will do the job and they are smaller but will solder in fine

    If they blow then you have other issues or bits missed
    Will do, will order them today and see how it goes. What method do you use for fitting to to the board? I have seen a number of recommendations from using solder paste and heat pencil to soldering iron on the tab till solder melts. Either method creates a lot of heat to the component. The legs are the easy part.

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by flocko
    Could you give the name of the UK seller you got the kit from, there are a lot of fake parts being sold in kits over here.my advice would be dont buy them. iI get boards sent to me for repairs all the time, most after buying IGBTs or kits from eBay,only to see the IGBTs blow on power up
    http://www.ebay.com.au/usr/mbtv_elec...53.m2749.l2754

    This is the site I purchased the kit. Seemed ok to deal with.

    Leave a comment:


  • dj01fad
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    I found 25 pcs on a private near my town a few months ago, at 35euros for all of them, and bought them. I used them and all worked fine. Now I am out of stock, and still waiting for the package from china (100 pcs). will see if they are ok. (I am a little worried)

    meanwhile, I received 6pcs 30f131 from panasonic service, and repaired a sn board from a P42GW30, and it is working perfect (non stop since yesterday). the funny thing is that they still have these on stock! i can take a some photos with the packaging from panasonic, and the 30f131 piece if you want. the tv is still open.
    Last edited by dj01fad; 11-17-2016, 04:46 PM.

    Leave a comment:


  • Moreno83
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    You also got them from china? I just ordered 100 pieces , see if they work or not

    Leave a comment:


  • dj01fad
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by tw2005
    Ok, normally the diodes survive.

    You could assume the parts may have been bad in which case you could order 10 FGD4536 from RS components and use them for q401,402,403,421,422,423 .

    they will do the job and they are smaller but will solder in fine

    If they blow then you have other issues or bits missed
    fgd4536 are working fine on my boards too - instead of 30f131, dg301, rjp30...
    Last edited by dj01fad; 11-17-2016, 05:51 AM.

    Leave a comment:


  • flocko
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Could you give the name of the UK seller you got the kit from, there are a lot of fake parts being sold in kits over here.my advice would be dont buy them. iI get boards sent to me for repairs all the time, most after buying IGBTs or kits from eBay,only to see the IGBTs blow on power up

    Leave a comment:


  • tw2005
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by Librian1969
    Just lifted the legs on q401,402,403,421,422,423 And d401,421. They are all shorted.
    Ok, normally the diodes survive.

    You could assume the parts may have been bad in which case you could order 10 FGD4536 from RS components and use them for q401,402,403,421,422,423 .

    they will do the job and they are smaller but will solder in fine

    If they blow then you have other issues or bits missed

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Just lifted the legs on q401,402,403,421,422,423 And d401,421. They are all shorted.

    Leave a comment:


  • Librian1969
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Yes correct, quick rundown. TV made a pop sound then went into 7 blink mode. Tested sc board, direct short at sc2 connector. Sd and Su boards tested ok. Ordered repair kit and replaced q401, 402,403,421,422,423. D401 & 421. Q531 & ic502. No short found at sc2. Refitted board and instantly failed. Showing direct short at sc2 again. And 7 blink mode.

    Leave a comment:


  • tw2005
    replied
    Re: Panasonic SC Board - BAD 30F131 IGBTs

    Originally posted by Librian1969
    Hi, I am having issues with a panasonic tnpa5335 sc board and hoping for some advice. I ordered a repair kit from the UK as well as replacement components from China. I fitted the UK kit, and with no short across SC2 I powered it up. Board failed immediately and after investigation found Q401 (30f131) had a direct short. I replaced Q401 and board failed again. SD and SU boards test ok. Any ideas as to where to next?
    What worries me is the missing details.

    If Q401 is short, 402 and 403 also would have to read short and if any of those shorted then it's pretty much assured Q421,422,423 are also shorted.

    Before you even started on this board what was shorted in the beginning?

    Leave a comment:

Related Topics

Collapse

  • Tynan Dill
    Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
    by Tynan Dill
    I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

    Upon bringing it home and plugging it up, it showed a standby light.

    I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

    The screen seems to blackout and stay black, but with a flashlight I can see the display.

    With my Playstation 4 connected via HDMI, and running a game I can hear sound.

    Assuming...
    11-22-2024, 01:46 PM
  • m1ch43lzm
    HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
    by m1ch43lzm
    Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
    Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
    05-12-2025, 08:37 PM
  • sam_sam_sam
    Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
    by sam_sam_sam
    I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

    This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

    After all of...
    07-13-2024, 08:14 PM
  • canadaboy25
    Panasonic TC-P54VT25 No image. A or D board?
    by canadaboy25
    I have a Panasonic TC-P54VT25 that will power on and prime the display but there is no image at all.

    The panel is primed as there is a slight glow from the entire panel. This means the problem should be logic related. The service manual also confirms this and recommends replacing the A or the D board.

    I have tried to get the TV to display the test sequence but I have been unable to and I don't even know if this TV has a test sequence or not. I tried following tom66's instructions in post #3 on this thread https://www.badcaps.net/forum/showthread.php?t=26790. There was...
    01-17-2021, 01:06 AM
  • stecos
    Panasonic Plasma main board repair (ST30 GT30 VT30 ST50 GT50 VT50),LED with 3 blincks
    by stecos
    Hi everyone!
    I happened several times, in the search for help from the web, to consult this very interesting forum.
    So I decided to sign up and I intend to participate actively by making available my knowledge and experience on the subject, I'm a new user but at the same time I'm old in the sense that I have 4 decades of experience in repairing and designing electronics but above all I'm a great passionate about the subject.

    Having said that I come to the gist of my post on the forum as the title suggests.
    For my passion for technology I'm now collecting several...
    11-28-2022, 11:39 AM
  • Loading...
  • No more items.
Working...