LG RZ-37LZ55 stuck in Standby

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Chungalin
    Badcaps Veteran
    • Jul 2014
    • 423
    • Spain
    #1

    LG RZ-37LZ55 stuck in Standby

    I’m stuck too with this one.

    Red Standby LED on. Doesn’t power on from keyboard nor remote. ST_5V (5V standby power) correct. ON/OFF signal to PSU is always 0V (so it’s normal that power supply doesn’t start other voltages). PWR_ONOFF signal from CPU is 3V, and this brings Q1001 to short ON/OFF with GND, so looks like it’s nothing from PSU (it looks good, nothing bloated, nothing blown and good ESR). Tried disconnecting all cables from PSU to MAIN, and shorting ST_5V with ON/OFF. Relay clicks, so it looks that PSU would power on if CPU could activate it.

    IR receiver signal present on MAIN connector from front PCB. Keyboard has 3V and reacts to Power keypress.

    So, to me, looks like a MAIN problem. Anything I can do?
    Last edited by Chungalin; 12-22-2015, 06:48 AM.
    Tags: None
    • fpsousa
      Member
      • Dec 2015
      • 29
      • Portugal
      #2
      Re: LG RZ-37LZ55 stuck in Standby

      Hi
      Yes, it seems to be the CPU chip that don´t produces the on/off signal.
      Has you measure the crystal clock frequency? and the voltages on main that suplies the CPU?
      Sometimes the eeprom must be exchanged and sometimes is a problem off firmware.

        Comment

        • Chungalin
          Badcaps Veteran
          • Jul 2014
          • 423
          • Spain
          #3
          Re: LG RZ-37LZ55 stuck in Standby

          Other small voltages (3.3V, 1.8V...) were correctly generated from the ST_5V.

          I’ve dismissed this one, no time to keep messing with it. Thanks for the help.

            Comment

            • sordids999
              Badcaps Legend
              • May 2013
              • 2161
              • uk
              #4
              Re: LG RZ-37LZ55 stuck in Standby

              http://www.ebay.co.uk/itm/LG-RZ37LZ5...AAAOSwqu9VGdDu

              7 Piece REPAIR Kit for LG RZ37LZ55 Power Board 6709900002A 6870TD30D10 EAY33043001 Repair Kit.


              Fixes the following symptoms:
              -stuck in standby
              -won't come on
              -dead

                Comment

                Previous template Next

                Related Topics

                Collapse
                • lepak06
                  TV LED 4K Selecline 65S18 ( T.MS3458.U801) stuck in Standby mode
                  by lepak06
                  Hello

                  I have an TV Led 4K Selecline 65s18 with mainboard T.MS3458.U801

                  The TV is faulty with stuck in Standby RED LED. Can't power the TV.

                  Before this problem , the TV stuck the picture with artefact , i unplug the AC cable and since the tv is stuck in standby .

                  All voltage are OK on PSU and main board for regulator. I tried flash firmware 25Q64 with many dumps

                  But the voltage on power button is 0.6V not 3.3V. When i press power button the voltage up to 0V. I tried to add 5V with Power Supply on 5V_STB and 3.3V on Power...
                  01-12-2023, 01:43 AM
                • toty79
                  Hisense LTDN50K220WSEU stuck in standby
                  by toty79
                  Hello to all friends of the forum and well found, here I am asking for your help and sorry for my translated English.



                  As per Hisense tv title LTDN50K220WSEU stuck in standby
                  PSU rsag.820.5687 HLL 4855WF
                  Main rsag 7.820.5842
                  I enclose the psu diagram, after the first routine checks I find myself with a regular standby voltage of 3.3v blue light on steady when the power button is pressed nothing happens, psu disassembled and bench checked ... forced ignition by sending a signal 3 , 3v on the SW and PWM2 pins the psu turns on and delivers all the voltages...
                  05-01-2022, 04:39 PM
                • lego1234567
                  LG 32LB1R - stuck in standby mode
                  by lego1234567
                  Hi. I have the following problem with my TV. After connecting to mains, the standby led (red) turns on, but TV is not responding to remote control or buttons on TV. After some measurements, I found out that +5 V standby voltage is present, but I dont have ON/OFF signal coming in to turn PSU on. It stays at zero volts. After looking at the schematic of the mainboard, I should get ON/OFF signal coming in at the R1402 resistor, but it stays around +3,5 V. So I removed it and I was able to turn on TV with buttons on TV, but not with remote control.

                  What could be the problem ? Thanks...
                  2 Photos
                  01-21-2024, 03:39 AM
                • Stunt
                  Hp Laptop Stuck on Hp protected by hp sure start screen
                  by Stunt
                  Hi guys i've got an Hp laptop Zbook 17 g5 Stuck on Hp protected by hp sure start screen.
                  I have tried almost every bios available on various platforms about this laptop but the problem is still the same.
                  I even successfully build my own bios using the one from the Hp website but the problem the laptop still getting stuck there.
                  Even if i try to press Esc key nothing happens. I tried f10 it doesn't go to bios still stuck there i just saw entering setup menu on the bottom left corner of the
                  screen that's it and stuck there. I left it until the following day and i still...
                  09-02-2025, 01:51 PM
                • Rusenga
                  Samsung UA39EH5003R Stuck on standby
                  by Rusenga
                  Hi techs, I have a Samsung ua39eh5003r which switches on and then goes to standby. I have to wait for a day or two for the tv to switch on again, all the time it is stuck on standby. I have checked the voltages on the power supply board on both occasions when it is on and off and these are my findings:

                  Connector CNM803:
                  TV ON
                  Pin1,3,4,5(Vamp),7(Vamp)- 12.6V; Pin2(PWM_DIM)- 0.96v; Pin6(BLU_ON/OFF)- 4.41v; Pin8,9,10- grnd; Pin11,12,13- 5.16v; Pin14(Power ON/OFF)- 3.3v

                  TV OFF
                  Pin1,3,4,5(Vamp),7(Vamp)- 12.6V; Pin2(PWM_DIM)- 0.06v; Pin6(BLU_ON/OFF)-...
                  09-18-2021, 11:51 AM
                • Loading...
                • No more items.
                Working...