it stops looping but I'm getting this screen when it loads up also tried jumping the second PSU but nothing...
sordids999
Badcaps Legend
Last Activity: 03-08-2026, 07:28 AM
Joined: 05-25-2013
Location: United Kingdom
-
With the jumper attached and lvds cable disconnected nothing still looping but with the spare PSU connected
it stops looping but I'm getting this screen when it loads up also tried jumping the second PSU but nothing... -
Samsung ue43tu7100 looping
TV is stuck in a boot loop tried all tape off methods but nothing the strange thing is I have 2 spare power supplies which instantly stops the boot loop but I have lines on the screen on both spare power supplies
So does this model have faulty panels and power supplies ?
Thanks... -
Just an update
Blocked 8 clock signals on the left hand side of the tcon board and it's been running for over an hour now and fingers crossed its good at the moment...Leave a comment:
-
On YouTube on smart option I'm not getting the black horizontal line going across everyone 5 secs but still have the top and corners with pixelated dots...Leave a comment:
-
More along the top...
Leave a comment:
-
Sony 55xd8005 pixelated on screen
Hi
Has anyone seen this before ?
At the top of the TV and the corners after 40 mins just below the top of the screen a black line shows horizontally but keeps going on and off every 5 secs
Panel fault ?
Pictures attached
Thanks...Last edited by sordids999; 01-16-2026, 06:40 AM. -
Hi
Got this model when the TV is playing you can still see the smart screen menu behind while playing a channel could this be the tcon at fault also The colours seem to be washed out just like a gamma fault ?Last edited by sordids999; 10-05-2025, 01:22 PM.Leave a comment:
-
Just an update on this post I had one of these come in no picture right side looking at the back of the TV AVDD is 17v left side is 7v on the left side I missed the first two traces out on the lvds connector then using a piece of paper about 3mm width blocked the faulty signalLast edited by sordids999; 10-05-2025, 07:27 AM.Leave a comment:
-
Leave a comment:
-
Any ideas ?'Leave a comment:
-
Got a 55xe8396 with 6 blinks fault replaced the backlights but still no backlights will light up
Voltages on led legend
Cn6801 +out3 =79v
Cn6801 +out2 =152v
​​​​​​Cn6802 no voltages
But the minute I connect the tcon board up the TV goes back into 6 blinks faultLeave a comment:
-
Just and update on this post replaced T2D34 diode and B117H TV now up and running
Thanks...Leave a comment:
-
Found T2D34 diode is shorted and B117H is also shorted
Ordering B117H but can't find T2D34 diode does anyone know and alternative ?Leave a comment:
-
I'm trying to repair this TV totally dead D501(T2D34 diode) is showing as shorted in circuit and out
Zd501,zd504,zd505 shorted in circuit but out of circuit there fine so stuck on trying to trace what causing the fault any ideas
Thanks...Leave a comment:
-
On my TV I have exactly the same fault and the same voltages on PL816 except for no 12v and no 5v bl_on still a main board fault?...Leave a comment:
-
Sorry just seen this message I cut the right side if I remember...Leave a comment:
-
Hi does anyone have the firmware for a Panasonic 50lx650 main board 17mb185
Screen ves500qnzh-n2-z01
23798312
Thanks...Leave a comment:
-
Hi does anyone have the firmware for a Panasonic 50lx650 main board 17mb185
Screen ves500qnzh-n2-z01
23798312Leave a comment:
-
Just an update on this TV issue changed the tcon and it's all working again
P.s thanks Davi.pLeave a comment:
-
If I disconnect lvds cable one at a time on the tcon
CLK1 to CKL10 is 9.8v
If both lvds cables are connected then
CKL1 to CKL10 is 0.00v...Leave a comment:
No activity results to display
Leave a comment: