Seiki SE39UY04 Red standby light, not powering on

[HughR]

Re: Seiki SE39UY04 Red standby light, not powering on

I have a problem with these symptoms: Seiki SE39UY04 Red standby light, not powering on

I will start a new thread because I think that's what I'm supposed to do. But first I have to post my first post as a new member. That's what this is.

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

Thanks for the follow-up on the repair.

You are most welcome. Thank you for all the help you have given me on even more than this one TV. I do appreciate your time and efforts.

[budm]

Re: Seiki SE39UY04 Red standby light, not powering on

Thanks for the follow-up on the repair.

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

Well the power supply fixed the TV and now I have a working 4K TV for 29.00

[michael dranfield]

Re: Seiki SE39UY04 Red standby light, not powering on

Thermal expansion due to heating and cooling can over a long period of time causes hairline cracks in the soldered joint resulting in an intermittent connection or even a burn up which is what you have , all you need to do is re solder the transformers pins with some fresh solder to prevent this happening again.

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

you might just want to re solder them any way , just in case dry joints on this transformer is a common fault in this model .It will prevent the same thing happening to the replacement board.

What is a dry joint?

I fixed one monitor I had called hanspree 28 inch 3ms gaming monitor and it still works to this day. So I know how to solder. I just dont get what you meay by dry joint? Does this mean that though the solder was administered it did not join properly to all areas of the joint?

[michael dranfield]

Re: Seiki SE39UY04 Red standby light, not powering on

you might just want to re solder them any way , just in case dry joints on this transformer is a common fault in this model .It will prevent the same thing happening to the replacement board.

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

BTW, when get the new board, inspection the solder joints on the legs of the transformers to the circuit board really well so it will not burnt up like the old board.

Will do.

[budm]

Re: Seiki SE39UY04 Red standby light, not powering on

BTW, when get the new board, inspection the solder joints on the legs of the transformers to the circuit board really well so it will not burnt up like the old board.

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

I ordered a new PSU and I will see if it fixes the issue and will post back to update this thread so at least it is useful in some way as there are no other posts for this model number on the forum.

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

BTW, this one looks like the AC input jack is damaged:
http://www.ebay.com/itm/Seiki-SE39UY...YAAOSw6dNWT2RS

Do you think its just possible this guy, when pulling the back off, pulled on the AC input jack and bent it a bit?

I mean, between those two choices in eBay one has three pins connected and a straight AC jack and the other has two pins connected and a bent AC jack.

lol

What a choice. I suppose I could spend a bit more money


Edit: I have looked at a seller on eBay who has a lot of these boards and some of them have two and some three. I suppose it is just connected on some and not on others. But the board on the bottom even on shopjimmy appears that that pin hole is just a ground.

[budm]

Re: Seiki SE39UY04 Red standby light, not powering on

'If you look at the two boards in those eBay listings they are the same in almost every way.

In one of them two leads are connected and in the other three leads are connected in the area that is blown out in my board.

My question is... any idea why that is?'
Per shopjimmy picture, that 3rd pin is not used, so the on;y to know is to look at the bottom side of the board that has all 3 pins to see if it is an active pin or not.

Seiki 890-PM0-3618 (MP3618-N) Power Supply Unit.
http://www.shopjimmy.com/seiki-890-p...pply-unit.htm#

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

What is the P/N as printed on your board barcode sticker?
Model: MP??????????

Below are all my board. I tried two different lighting types in case it didnt show up well and figured I would supply a full picture of the PSU.

[budm]

Re: Seiki SE39UY04 Red standby light, not powering on

BTW, this one looks like the AC input jack is damaged:
http://www.ebay.com/itm/Seiki-SE39UY...YAAOSw6dNWT2RS

[budm]

Re: Seiki SE39UY04 Red standby light, not powering on

What is the P/N as printed on your board barcode sticker?
Model: MP??????????

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

Figured I would just post the problem here because once I took the back cover off the problem became very apparent.













I think it is very obvious the PSU is bad. Usually it isn't this obvious.

So my question would be.

I have saw this board here.......

http://www.ebay.com/itm/Seiki-SE39UY...YAAOSw6dNWT2RS


And here.....

http://www.ebay.com/itm/SEIKI-SE39UY...EAAOSwXshWsSd3



If you look at the two boards in those eBay listings they are the same in almost every way.

In one of them two leads are connected and in the other three leads are connected in the area that is blown out in my board.

My question is... any idea why that is?

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

The OP never come back after I requested for the Voltage readings.
You should start a new thread amd make sure to put make and model on the thread name, then upload good clear pictures of the whole back side of the TV so we can see all the boards, and pictures of each board.

Will do. Thanks

[budm]

Re: Seiki SE39UY04 Red standby light, not powering on

Have you figured this problem out?


I have this TV and I have a solid red light on at all times as soon as you plug it in and no picture. Remote does nothing.


What should I do?

Thanks

The OP never comes back after I requested for the Voltage readings and pictures.
You should start a new thread amd make sure to put make and model on the thread name, then upload good clear pictures of the whole back side of the TV so we can see all the boards, and pictures of each board.

[abeeftec]

Re: Seiki SE39UY04 Red standby light, not powering on

Have you figured this problem out?


I have this TV and I have a solid red light on at all times as soon as you plug it in and no picture. Remote does nothing.


What should I do?

Thanks

[budm]

Re: Seiki SE39UY04 Red standby light, not powering on

We need to find out first as to what Voltages you have at the connectors as I suggested.