Re: usp440m-42lp psu
Perfect. What's the voltage at the points indicated in the picture?
Perfect. What's the voltage at the points indicated in the picture?
Attached Files
-
-
Re: usp440m-42lp psu
????
Are you sure the fuse is ok?
You measure AC, right?Comment
-
Re: usp440m-42lp psu
i did a continuity test on it, i took the fuse out of its holderComment
-
Re: usp440m-42lp psu
Check input voltage directly at the connector. Sure it's there?Comment
-
Re: usp440m-42lp psu
Nothing. Extension lead is fineComment
-
Re: usp440m-42lp psu
Well, then the problem is somewhere else. I don't have the TV in front of me, just the board. Check the connector/cable etc.Comment
-
Re: usp440m-42lp psu
That's very strange. Is your multimeter working? What if you measure the AC directly at the wall outlet?Comment
-
Re: usp440m-42lp psu
There is also an EMI filter directly connected to the AC inlet of the TV. Maybe it's faulty. You could measure the output voltage at its terminals.Attached FilesComment
-
-
Re: usp440m-42lp psu
gonna have to give it a break tonite, will go over these bits tomorrow.Comment
-
Re: usp440m-42lp psu
ok. good luck. Shouldn't be hard.Comment
-
Re: usp440m-42lp psu
Ok, keep us posted about your findings. There is not much left to check.
In the meantime I will spend another evening on my board
Comment
-
Re: usp440m-42lp psu
How did this work out for you? Was it the Filter?Comment
-
Re: usp440m-42lp psu
Great. Good luck!Comment
-
Hi guys
I need one of these MP2329CGG for a repair job. It's a 24V 6.5A buck converter. But I have not been able to find a supplier who has that component.
Actually I would buy a few as I always think if I found one faulty already I will probably find more in the future
I had one supplier on Aliexpress who gave me a price $2 each, but I have been waiting some days since I asked for shipping price and they don't reply
Does anyone know where I can buy that part in small quantity (let's say 5 of them), or any equivalent I could use? it supplies the Standby... -
Hello, although I've never been formally taught soldering techniques, etc... I've not really run into too much trouble soldering, with the exception of this job...
I've got a supposed blown transistor on my fuel pump on my car and I'm trying to replace it. It's a gel encased circuit booard with very fine connections. Please see photo uploaded.
I've cleaned up the area that I'm working on with alcohol scraped off the wires, etc..
I cannot get any solder to now stick any of the connections, I've used various grades of solder and flux combination, nothing... -
Hello friends. I have been struggling with this device for several months. The problem is that the laptop is 6th generation and every BIOS I find is 7th generation. In the BIOS settings, it says Kaby Lake in the integrated graphics. The graphics drivers are not installed properly in Windows either. I would be grateful if any of my friends could help me finish this laptop.
Model : Alienware 17 R4 (6th gen)
Motherboard : LA-D753P rev 1.0(A00)
CPU: 6820HK -
I have a very strange issue here. Customer was using Mac one day and stopped working when they went to use it the next day. I plugged it into my amp meter and I got 5v at 0.10amp.
Checked all rails:
PPBUS_AON: 12,3 V
PP3V8: 3.79v
PP3v3_AON: 3.29v
PPDCIN_AON_CHGR_R: 5 V
The very strange part of the issue is that I left the Mac on one side for a day, came back to it and reconnected everything. Connected the DFU cable to a WS machine and connected the charger. The Mac then booted to the login screen? I then logged in and because I was after... -
Hi all,
I had recently tried to reflash the bios on a dell latittude that has a Wson8 Chip however to no avail.
My question is, Has anyone had much success using the Pogo/Needle adapters to read and write bios without removing the chip from the main board?
I seem to struggling with the solder process wofh my reflow station and currently have 4 machines waiting for a bios mod/reflash.
For context I have just ordered a EZP2019 SPI flash so this is what I would be using alongside the Pogo Adapter.
Apologies if this is the wrong subcategory....
Comment