Hi guys just got this plasma 10 red flashes
Any ideas
Any ideas
-
-
Re: Th-42px80ba
Try a search--Its been covered recently.....TELEFIX
How PLASMA SCREENS WORK, X-SUS and Y-SUS what they do--
http://www.irf.com/technical-info/appnotes/an-1088.pdf
PLEASE DO NOT EMAIL ME PRIVATELY FOR REPAIR ADVICE. QUESTIONS BELONG ON THE FORUM! -
Re: Th-42px80ba
Thanks mate for the reply searched around i cant find much infoAttached FilesComment
-
-
Re: Th-42px80ba
Check PSU 15V. Is it good?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Th-42px80ba
Checked all voltages from the schematic p12 p6 p7 p25 no voltages,all i get is a clicking sound on the psu when its turned onComment
-
Re: Th-42px80ba
Have you checked fuses F401+F402 and Q406 for short on the power boardComment
-
Re: Th-42px80ba
Fuses seem okComment
-
Re: Th-42px80ba
Try unplugging SC and SS ribbon cables, does blink code change to 6/7/8 blinks?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Th-42px80ba
disabled both cable ribbons but still getting 10 red blinksAttached FilesComment
-
-
Re: Th-42px80ba
OK ribbons back in what's the voltage you get on connector P6 (power board) pin 7,8,9, multimeter black on chassis ground, red on pin.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Th-42px80ba
pin 7 2.0 volts
pin 8 0.8 volts
pin 9 0.8 volts
these measurements are when the tv is first turned on but quickly drop to zero after a few minutesComment
-
Re: Th-42px80ba
Can you hold the reading on pin 7 as the TV clicks on and off and note any changes in the voltage? Go from unplugged to 10 blink code.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Th-42px80ba
pin 7 15.35 volts when the TV is first turned on then drops to 2.35 volts after the clicking sound,then keeps dropping until zero voltsComment
-
Re: Th-42px80ba
OK, now try pin 1 and hold the reading in the same way.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Th-42px80ba
pin 1 1.0 volt then again it drops to zeroComment
-
Re: Th-42px80ba
OK, now check pin 11 of P25; the PANEL_MAIN_ON. It should turn HIGH for +15V(S) to turn on, which is pin 1 of P6.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Th-42px80ba
Pin 11 of P25 nothingComment
-
Re: Th-42px80ba
OK, this is looking like a main board fault.
I've got a PZ70BA right now with a similar problem.
Does set have any fans -- if so do they spin at all?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Th-42px80ba
No fans tomComment
-
Re: Th-42px80ba
Ill try and find a replacement board thanks tomComment
-
Hello guys, i need help with this problem, I have a NM-D041 mobo, it came with low impedance in 3v linear regulator rail, the cause was a damaged EC controller ITE8227e-192. I ordered a new one and replaced it. This laptop have a different chip for keyboard management and it8227e pins for programming ITE chips are not accesible through keyboard interface, I flashed it using i2c interface pins with vertyanov programmer because laptop was dead and SPI flash didn't have power (only 3v EC) so it couldn't access firmware stored in SPI memory. I read SPI and extracted it8227 firmware from original BIOS... -
I am a hobbyist (not a professional) so please be gentle...
I recently received an XR-77A80J that wouldn't turn on. (Repeating 5 flashes when plugged in.)
I did a hard reset by holding the power button for about 30 seconds until the set powered down. I then tried to turn it on and it powered up, bringing me to the setup screen. There's not a lot of detail on the setup screen but the picture didn't have any distortions, so at least a cursory examination suggests no physical damage to the screen. The set appeared to be working normally, but it shut down after about 15 seconds,... -
Hello, I'm new to the group and to trying to repair a LCD TV. During the past few years, I've been collecting/repairing/restoring vintage personal computers (Commodore, Apple II, Atari, TRS-80, Texas Instruments, and Timex Sinclair). This has been my retirement hobby. Now I've gotten interested in trying to repair a LCD TV that I have and used regularly when working on vintage computers.
The LCD I'm working on is a Insignia NS-LCD019. I've downloaded the service manual that I could find, but it must be a different revision since not too many items in the service manual match the TV... -
I finished my work for this year, so I'm free until January 6th.
My last task it's unresolved and I'm looking for ideas for the return in January.
So what's about...
This laptop is booting in 3-4 seconds has no password and every voltage is present. So far so good.
My problem is that it doesn't boot from anything. !...just stays with a blank screen(backlight only)
No USB boot (in fact partially no boot...), no PXE boot nor boot from M2.SATA or NVME...crazy...
The Ventoy USB (EFI) boots in the menu system but after selecting one of the ISO (like a simple... -
I have an Hp x360 15-u499nr laptop with a continuous white blinking power light. The laptop does turn on. The light flashes with just the battery and if I disconnect the battery and just use the power cord it still flashes and with both connected it still does. I have updated the bios and tried a hard reset with battery unplugged and power cord unplugged and holding down the power button for 60 seconds. I can't think of what else to try.
Comment