Proper way to test IPM??

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • topfli8979
    Badcaps Veteran
    • Oct 2012
    • 311
    • USA
    #1

    Proper way to test IPM??

    I finally pulled a bad IPM off a vizio p50hdtv10a y sustain without destroying the board. Anyone know the sequence to test it? It does not have any identification numbers on it anywhere.
    Attached Files

    if you find these attachements useful please consider making a small donation to the site

    Tags: None
    • kevinm34232
      Badcaps Legend
      • May 2012
      • 1884
      • USA
      #2
      Re: Proper way to test IPM??

      This looks like your IPM: (This is from their blog)

      http://blog.coppelltvrepair.com/2010...71qyh039a.html

      You will make 3 tests on each IC.

      If any of them results in continuous beep and reading of “0” (or the same reading on the display as you get when you touch the two probes of the meter and hear beep) then the IC is bad.

      You will be testing:


      1) VS to GND
      2) VS to SUS_O
      3) GND to SUS_O

      Each of the contacts (VS, GND and SUS_O) has multiple pins on the IC, i.e. all pins in the group are the same and it does not matter which one you will try on.

        Comment

        • topfli8979
          Badcaps Veteran
          • Oct 2012
          • 311
          • USA
          #3
          Re: Proper way to test IPM??

          Well according to this test, this IPM is good, I get no beeps on any of the pins. The tv was flashing white and clicking sound coming from what seemed to be this ipm. I cant imagine it being the upper IPM, other forums say its rare for the "er" ipm to fail.

            Comment

            Previous template Next

            Related Topics

            Collapse
            • chth96
              How Can I test PWM DM0365R?
              by chth96
              Hello
              I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
              So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
              I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
              I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
              06-18-2025, 04:14 PM
            • khelane
              test active pfc power with lamp test
              by khelane
              Hello
              I have a big problem and that is that in some cases when repairing active pfc power supplies I cannot work with a test lamp. I can only get help with 5 volts standby and for starting and starting I have to work without a lamp and this way there is a possibility of parts exploding and other parts being added.
              Sometimes with a multimeter test the problems can be reduced to some extent, but I had several cases that had to be tested on and online and recently two varistors exploded. They had terrible resistance because the power supplies were over 800 watts.
              Is there a way...
              06-03-2025, 01:00 AM
            • chronic519
              Mats / mods: detected and repaired GPU fault. Cant seem to test after!
              by chronic519
              Hello.

              GPU came in, green lines. Spent lots of time using to get the Mats / mods drive working (found on youtube).
              Found issue with a RAM block
              Replaced, green lines gone.
              Trying to test again, assuming getting the false positive. Originally had over 1K on a single bank. Now getting tosses low between banks.
              Used a good card to test and same results low errors 32+.

              I am just search for some form of command to do a full test on the GPU.
              I just ran the mats command with my good GPU and passed after roughly 40 min.
              The repaired one, ran...
              05-20-2025, 07:56 PM
            • hemant_2222
              Yamaha 2064 No sound but Test audio working
              by hemant_2222
              Hello Guys,

              Greetings!

              Hope you all are doing well.

              I am looking for suggestion on Yamaha 2064. The problem with this receiver is that it has no sound however when the test tones are activated it does outputs from all the speakers. It is working in two channel stereo mode but when you select other sound modes, it doesn't. The last time it had a problem, I had replaced the DAC
              PCM1681DBQR - IC263 and it worked fine.

              Other issue with it is one of the STK ICs is getting more heated then the other one but that can be looked at later.
              ...
              11-01-2025, 11:20 PM
            • alltvrepairs
              Lg TCon test pins for screen test
              by alltvrepairs
              Hi,
              i have a 65 Panasonic TX-65HX710E using vestel 17MB170 main and Lg tcon.

              Few drops of water fell probably near COF and have no display. Tried removing tabs but no.part of display present as if tcon fuse open. However 12v is present and tcon can be felt warm enough that supplies are present. Backlight and sound ok.

              Anyone knows if this TCon 6870c-0805A has any special test pins for rgb test?

              Appreciate your help....
              2 Photos
              06-13-2025, 06:33 AM
            • Loading...
            • No more items.
            Working...