Replacing a bad cap on TV

Collapse
X
Collapse
 
  • Page of 4
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 template Next
  • justjoe
    Member
    • May 2013
    • 35
    • England
    #61
    Re: Replacing a bad cap on TV

    Ok fixed the new problem, there is a small screw on that tab panel that controls the gamma (i think) and i turned it slightly clockwise when i first discovered it hoping it would fix the screen fade but its actually given me that screen flicker, so ive turned it back to how it was and now im getting a good picture again.

    so all fixed then, lesson learned there, just strip it down and rebuild it and hope it works is the answer lol

      Comment

      Previous 1 2 3 4 template Next

      Related Topics

      Collapse
      • BigPete
        Panasonic Heatpump Dryer Repair
        by BigPete
        I picked up a Panasonic NH-P70G2, though it would apply to the NH-P80G2, NH-P70G1 and NH-P80G1 models as well, as maybe some other models. This one was coming up with a H86 error. After lots of testing and googling it was an error with one of the thermistors in the condenser area.
        The attached French service manuals is incorrect, TH11 is gray and is a 95k thermistor and TH12 is black and is a 35k thermistor.
        In my case TH12 was bad. I was able to get a 35k thermistor on AliExpress. It's 6mm in diameter.
        Unfortunately the whole machine has to come apart to fix it.
        I have...
        11-01-2025, 06:40 PM
      • AquaMan Ua
        Problem with PANASONIC CF53 laptop after changing BIOS settings
        by AquaMan Ua
        Hello. I am asking you for a hint on how to solve the problem with my touchbook Panasonic CF53-2 standart model. After setting up the BIOS, the laptop displays the wrong image until Windows loads. (More precisely, it displays, but distorted, instead of the Panasonic image immediately after turning it on, it displays what is in photo #1 in the attached file) Then the image appears when Windows starts loading and then there are no problems with the screen until the reboot. If you enter the BIOS, just a black screen. If you connect an external screen, the image on it is the same as on the built-in...
        2
        2 Photos
        05-17-2025, 09:40 AM
      • Alfieh
        NAD C320BEE repair possibly bad capacitors
        by Alfieh
        hey Im very new to repairing electronics with capacitors as well as using a multimeter so I need so help/guidance fixing this issue

        recently I was handed a family members old NAD C320BEE that they had in their loft for storage for a few years but when powered on it went into power safety mode due to a problem on the protection circuit somewhere before it went into storage I was told it worked fine I found lots of people online talking about how the capasitors are known to be pretty bad in this model and can cause this issue the only problem being I don't have much experience sorting...
        11-19-2024, 04:55 PM
      • Andre Gilbert
        Panasonic TC-P55ST50 8 blinks then no blinks
        by Andre Gilbert
        Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
        Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.

        TV Model: Panasonic TC-P55ST50
        ...
        1 Photo
        11-20-2024, 08:52 PM
      • yuzupatogik
        Help with replacing Capacitors on Altec Lansing ATP 3
        by yuzupatogik
        Hello,
        I have this old (2004?) Altec Lansing ATP3 and i would like to replace the capacitors. I have identified 34 out of the 36 of them as Samxon GR of various capacities and voltages.

        I can't find datasheets for the Samxon in any of the following variants:

        10000uF 25 v - this one i really want to replace because i suspect it is what causes a dull hum regardless of the volume knob position or if the source is plugged in. I am eyeballing the Rubycon 25PK10000MEFCGC18X35.5 for this purpose. So if i pay a 10x the price part for shipping i might as well go ahead and...
        02-14-2025, 04:11 PM
      • Loading...
      • No more items.
      Working...