Proscan 40LD45Q 40" LCD TV Help Needed!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • DJJASON
    New Member
    • Aug 2018
    • 1
    • United States

    #61
    Re: Proscan 40LD45Q 40" LCD TV Help Needed!

    So, what was the result of replacing the 5PF 6KV Ceramic Caps?

    I have the same malfunction.

    Instead of the "Repair Kit" for $10, where can I order just the Caps?

    The Tv is all apart, sitting on my basement floor, and my wife is getting upset!

    Comment

    Related Topics

    Collapse

    • x_orange90_x
      Vizio E55-E1 bad backlights or bad inverter?
      by x_orange90_x
      I just got this tv today and it appeared to have no backlight on. After taking off the rear cover and checking again in the dark I can see that MAYBE one quadrant is lit.. But still it's quite dim. I was going to check the LEDs with my tester, and I found LED 1 and LED 2 + pins on the wire from the inverter, but I couldn't identify a ground. Nonetheless I tried using a mounting screw on the inverter board and also the chassis as ground but regardless my tester reads 300 which is what it reads when there is no voltage draw.

      I don't know how exactly to test the inverter itself. Is it...
      01-29-2025, 09:24 PM
    • blind2reply
      proscan 40ld45q - no pic -no sound - no backlight - blue light turns off
      by blind2reply
      proscan 40ld45q

      Have tried published resets with no help. (unplug for 10, push on-off for 30, push menu and vol +, etc.)

      After being plugged in, red light comes on. Push power button and blue light comes on for ~five seconds then goes out. Power button does not turn the unit on a second time - have to unplug/re-plug before power button will try to start with blue light.

      No sound, no picture (used flashlight test).

      No bulging cap, no burn spots, no burn smells, nothing visual (cold joints/breaks/bugs).

      Digital voltmeter;...
      06-06-2021, 01:16 PM
    • Gentian
      APSINT3636VR 3600W APS INT Series 36V DC 230V AC Inverter/Charger schematic
      by Gentian
      I have a tripp-lite aspint 3636vr inverter charger which blow some of mosfet transistors. I replaced them repaired also the driver circuit and tested but the mosfets burn again.

      It work very well as inverter and also as charger if I let the rear switch in auto mode (inverter) and charger only(charging) but in auto when I connect the feed line 220V AC first time it pass ok to line and start charging the batteries but when I remove the feed line it pass to inverter mode and if I do it again the second time when passing from charging to inverter the Main transformer start making a...
      03-06-2023, 07:07 AM
    • valvashon
      Insignia NS-LCD19-09 (PS OK, Inverter problem?)
      by valvashon
      For some reason I'm just not going to let this 19" TV defeat me. I guess because I have a schematic to work from I feel like I'm oh so close.

      History- while adding a turn-on circuit I let a small screw roll under the power board. Worked through all of that circuitry, probably replacing a MOSFET and PWM controller that were not bad but I was following the service manual. Finally figured out that the power supply is in working order when the inverter section (for the backlights) is disconnected. When the +12 supply to the inverter is disconnected the +12 and +5 will come up...
      01-04-2024, 01:44 PM
    • eccerr0r
      A modified sine wave inverter + a grid tie inverter?
      by eccerr0r
      If I had a solar fed grid tie inverter (GTI), a modified sine wave inverter, and a power outage occurred, what would happen if you disconnected mains, backfed the modified sinewave inverter (MSI) into house power, and hooked up the GTI to the output of the MSI, would it work?

      Next thing is trying to charge the batteries using solar power, but that's another issue ...
      08-31-2023, 09:14 PM
    • Loading...
    • No more items.
    Working...