Advice needed-Technika 32-207 works but sticks on channel,won’t change channels ok

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • rustinjust
    Member
    • Jun 2022
    • 49
    • England

    #1

    Advice needed-Technika 32-207 works but sticks on channel,won’t change channels ok

    My tv will work for a while and change channels with the remote as it should but then it will stick on one channel only and work ok but it won't change channels. I have tried unplugging it for hours and whilst unplugged pressing the power button on the tv to reset it.

    The volume button on the remote still works but it just won't change channels once it decides to stick on one channel

    It has built in basic freeview tv here in the uk, I've tried doing an automatic search to reset the tv but nothing works.

    I have to turn the tv off and then on again with the remote in order for me to get out of it being stuck on a channel.

    Question it likely a faulty component in the tv causing this ? And which component ?

    Any good advice appreciated
  • nomoresonys
    Badcaps Legend
    • Jan 2013
    • 12187
    • U.S.

    #2
    Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

    Did you try changing channels with the tv buttons?

    Comment

    • rustinjust
      Member
      • Jun 2022
      • 49
      • England

      #3
      Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

      Originally posted by nomoresonys
      Did you try changing channels with the tv buttons?
      I just tried it on the tv itself and it won’t change channels once it stays only on one channel. The tv when I first turn it on will change channels on the remote or on the tv itself for a while but after a while such as 5 or 10 mins it won’t change channels. The volume button on the remote will still work even if it won’t change channels.

      Sometimes after pressing the changing channels button it will change channels a long time later and other times not at all. What’s the likely problem? A bad capacitor or another component?

      Also, earlier before it wouldn’t change channels but then I pressed the up and down button lots of times on the remote and it moved but the screen went black/blank, then I pressed the standby button to reset it and the light on tv flashed blue and flashed on and off for around 20 times or so then it stopped on solid blue which is the colour it goes to when it’s working ok. Only when it stopped blinking on and off was I able to turn the tv on again with the remote.

      Tv is a Technika Lcd 32- 207

      Also…. Would this board help fix the problem ? https://www.ebay.co.uk/itm/324304452175
      Last edited by rustinjust; 09-28-2023, 03:55 PM. Reason: Changes

      Comment

      • nomoresonys
        Badcaps Legend
        • Jan 2013
        • 12187
        • U.S.

        #4
        Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

        might not help but try a simple reset, unplug tv for 5 minutes, hold power button in on tv for 30 seconds then plug tv back in and try it. An update might help.

        Comment

        • EazyBone
          Badcaps Legend
          • Jun 2023
          • 1328
          • United states

          #5
          Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

          Use remote. Turn camera on smart phone and face it at the top of the remote, hit the buttons on remote and camera will pick up infrared flash if the channel buttons are working on remote. I know you said tv buttons also but maybe they both not working.

          Comment

          • Davi.p
            Hobbist Tech
            • Sep 2009
            • 4326
            • Italy - Milan

            #6
            Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

            Use remote. Turn camera on smart phone and face it at the top of the remote, hit the buttons on remote and camera will pick up infrared flash if the channel buttons are working on remote. I know you said tv buttons also but maybe they both not working.
            obviously it is not there the problem, there must be a problem in the standby software or main software, since you are not a tech i suggest you to carry it to a service center to reprogram it..
            second possible chance is bad soc soldering..
            Last edited by Davi.p; 09-28-2023, 10:03 PM.

            Comment

            • rustinjust
              Member
              • Jun 2022
              • 49
              • England

              #7
              Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

              Originally posted by nomoresonys
              might not help but try a simple reset, unplug tv for 5 minutes, hold power button in on tv for 30 seconds then plug tv back in and try it. An update might help.
              I have already tried that last week, didn't fix it.

              Comment

              • rustinjust
                Member
                • Jun 2022
                • 49
                • England

                #8
                Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                Originally posted by EazyBone
                Use remote. Turn camera on smart phone and face it at the top of the remote, hit the buttons on remote and camera will pick up infrared flash if the channel buttons are working on remote. I know you said tv buttons also but maybe they both not working.
                The remote does change channels sometimes, for maybe 5 or 10 minutes after I’ve first turned the tv on, which is why I think the issue is with a component inside the tv itself rather than a remote control problem.

                Also I’m iunsure what you mean by turn my phone camera on, do you mean put my phone camera on to video mode to pick up the infrared from the remote? If so I don’t think the remote is the issue as it changes channels just fine at first for a while, then it will stick on one channel and won’t change channels. I’m thinking a bad cap or comoonebt

                Another question after you’ve read the above information would this board likely fix the problem if I bought it? Which board on my tv, link here to board https://www.ebay.co.uk/itm/324304452175
                Last edited by rustinjust; 09-28-2023, 10:44 PM. Reason: Make changes

                Comment

                • rustinjust
                  Member
                  • Jun 2022
                  • 49
                  • England

                  #9
                  Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                  Continuing on from more information above, would this board fix the issue
                  https://www.ebay.co.uk/itm/263267032623

                  Comment

                  • nomoresonys
                    Badcaps Legend
                    • Jan 2013
                    • 12187
                    • U.S.

                    #10
                    Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                    So you want to buy a new board before trying a simple update.

                    Comment

                    • Diah
                      Badcaps Legend
                      • Feb 2013
                      • 6370
                      • Germany

                      #11
                      Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                      Originally posted by rustinjust
                      Continuing on from more information above, would this board fix the issue
                      https://www.ebay.co.uk/itm/263267032623
                      yours TV used Vestel mainboards
                      you can try to log in service menu and from there do hard reset to reset yours TV as new..
                      service menu of vestel pressing menu on RC followed with 4 , 7 , 2 , 5 .

                      if didnt work google after vestel service menu

                      Comment

                      • yokoono
                        Badcaps Veteran
                        • Apr 2010
                        • 486

                        #12
                        Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                        MENU, 4725, Diagnostic, Factory reset, OK.

                        Comment

                        • rustinjust
                          Member
                          • Jun 2022
                          • 49
                          • England

                          #13
                          Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                          Originally posted by nomoresonys
                          So you want to buy a new board before trying a simple update.
                          What simple update? How?

                          Comment

                          • rustinjust
                            Member
                            • Jun 2022
                            • 49
                            • England

                            #14
                            Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                            Originally posted by yokoono
                            MENU, 4725, Diagnostic, Factory reset, OK.
                            I got in to the service menu and pressed factory reset, it then said press green so I pressed green button and tv went in to standby. Now tvs back on. Hopefully this will fix it. I’ll keep you all posted
                            Last edited by rustinjust; 09-29-2023, 11:19 AM.

                            Comment

                            • EazyBone
                              Badcaps Legend
                              • Jun 2023
                              • 1328
                              • United states

                              #15
                              Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                              Originally posted by rustinjust
                              The remote does change channels sometimes, for maybe 5 or 10 minutes after I've first turned the tv on, which is why I think the issue is with a component inside the tv itself rather than a remote control problem.

                              Also I'm iunsure what you mean by turn my phone camera on, do you mean put my phone camera on to video mode to pick up the infrared from the remote? If so I don't think the remote is the issue as it changes channels just fine at first for a while, then it will stick on one channel and won't change channels. I'm thinking a bad cap or comoonebt

                              Another question after you've read the above information would this board likely fix the problem if I bought it? Which board on my tv, link here to board https://www.ebay.co.uk/itm/324304452175
                              I mean turn your camera on like to photo, and just point it at the top of the remote. It will show a flash on your remote every time you hit a button. If it isn't flashing then that's the issue. Simple to rule that out, it probably isn't but is good to check

                              Comment

                              • rustinjust
                                Member
                                • Jun 2022
                                • 49
                                • England

                                #16
                                Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                                Originally posted by yokoono
                                MENU, 4725, Diagnostic, Factory reset, OK.
                                Update: I tried that and it hasn't worked. If I buy a main board will that fix the issue?

                                Comment

                                • rustinjust
                                  Member
                                  • Jun 2022
                                  • 49
                                  • England

                                  #17
                                  Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                                  Question: would a replacement main board fix the issue or is it one of the other boards inside the tv with the fault? Which capacitor/component is responsible for changing channels?

                                  Comment

                                  • Davi.p
                                    Hobbist Tech
                                    • Sep 2009
                                    • 4326
                                    • Italy - Milan

                                    #18
                                    Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                                    replace main board

                                    Comment

                                    • vinceroger69
                                      Badcaps Legend
                                      • Mar 2012
                                      • 6714
                                      • uk

                                      #19
                                      Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                                      Originally posted by rustinjust
                                      Continuing on from more information above, would this board fix the issue
                                      https://www.ebay.co.uk/itm/263267032623
                                      this is a t con board and not the mainboard the mainboard is the one with hdmi/tuner on etc make sure all numbers on replacement board matches your old one.
                                      (board should look like this) https://www.ebay.co.uk/itm/264916707...4aAhIkEALw_wcB
                                      Last edited by vinceroger69; 09-30-2023, 01:19 AM.

                                      Comment

                                      • rustinjust
                                        Member
                                        • Jun 2022
                                        • 49
                                        • England

                                        #20
                                        Re: Advice needed- Tv works but then sticks on a channel and won't change channels ok

                                        Originally posted by vinceroger69
                                        this is a t con board and not the mainboard the mainboard is the one with hdmi/tuner on etc make sure all numbers on replacement board matches your old one.
                                        (board should look like this) https://www.ebay.co.uk/itm/264916707...4aAhIkEALw_wcB
                                        There is also this main board without the small board attached on a wire that’s in the link you sent https://www.ebay.co.uk/itm/263267032623

                                        I’ll get the one that matches the number on my board cheers
                                        Last edited by rustinjust; 09-30-2023, 03:17 AM.

                                        Comment

                                        Related Topics

                                        Collapse

                                        • spleenharvester
                                          Reverse engineering of 18650 4-channel tester
                                          by spleenharvester
                                          Hi friends

                                          I have reverse engineered this tester, schematic is attached and is complete except for capacitor values. These testers annoyingly have no model number but they are the ones you find on the first page of just about any website if you type in "18650 4-channel tester". There is also a 2-channel variant and a newer 8-channel variant. They are very cheap (about £15) and can measure voltage, current, internal resistance and capacity. They have a multicolour display for all these statistics. They also have terminal blocks so that if you want to use a breakout board...
                                          05-04-2025, 02:43 AM
                                        • Camarada78
                                          Carvin PA620 shutting down
                                          by Camarada78
                                          I have a Carvin PA620 powered mixer with a weird problem: channel one shuts down the entire speaker output when plugged in. Its not a short because it still outputs sound through the line outs.

                                          1. voltages are somewhat correct (-42/+42, -26, -17/+17, when it should be +-43, -24, +-18).
                                          2. Channel 2 if plugged works normally, no issues, any volume.
                                          3. Channel 1 if plugged very low volume, works normally. if goes a little louder, it shuts down everything (both speaker channels)
                                          4. line out works normally in any situation, even after shutting down the speakers.
                                          ...
                                          10-15-2024, 12:07 PM
                                        • dicky96
                                          American Audio VLP1500 Distorting on one channel
                                          by dicky96
                                          Hi guys I have a VLP1500 amplifier here - one channels works fine and the other channel distorts even at low volume settings

                                          Protection and Clip LED are off

                                          There is something wrong with the BIAS voltages around T16 and T18 (in particular) on the bad channel

                                          I tested all diodes and transistors in this area in circuit with diode mode - both channels seem identical. Same in resistance mode across all the resistors here.

                                          The output DC voltages on pin1 and pin8 of the 5532D dual op amp at the input of each amplifier module are the same, and the audio...
                                          07-13-2022, 05:25 AM
                                        • dicky96
                                          I need to block a UHF channel but not sure how to do it
                                          by dicky96
                                          Hi guys
                                          I couldn't really find a section on the forum for this question so I guess I will put it here

                                          I do a lot of work in one of the local apartment hotels (an apart-hotel they call them here)

                                          Mostly I am maintaining the equipment in the 'TV' room or at the pool bar

                                          Anyway, I have a problem with the system in the TV room - most of this was a system I 'inherited' off the previous technician who no longer lives on the island

                                          Basically they have (see pic it probably explains it better) the following system. The UHF cabling is daisy chained...
                                          01-31-2022, 05:24 AM
                                        • sima112
                                          Marantz pm 6005 right channel not worknig
                                          by sima112
                                          Hi guys,
                                          I need a help with my Marantz pm6005. It started to have weaker the right channel a few months ago, than it got back to normal and now it has lost sound completely on the right channel. At the final stage it was loosing the channel for a while and than it returned. After it has disappeared completely I could forced it back by unplugging the source form CD (which I normally use) to phone and back. It would then work for a few minutes and died again. Now it is possible power up and all function works normally (apart the right channel ) on all inputs, except the phone both channel...
                                          01-30-2023, 12:11 PM
                                        • Loading...
                                        • No more items.
                                        Working...