Dual output power supply 5 and 12 volts (no output)
Collapse
X
-
Re: Dual output power supply 5 and 12 volts (no output)
Sorry, I think I don't understand what I have to do exactly,
"What are you using as a" tester "? If it is a dvm or multimeter, just check the voltage with the ground on the negative lead of the 68µf / 400v capacitor and then on the DRAIN of the mosfet.
Also check and post the voltage on each pin of the ic
Pin1 =
pin2 =
etc. "
I first have to check the voltage between the negative of the big capacitor and the drain of the mosfet right? Then should I put the negative probe on the ground of the IC and test all the other pins with the positive probe?Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
You can use the negative lead on the big capacitor for all the tests, that is what is called HOT ground.
Check that there is voltage on the drain of the mosfet (that is the center pin) be careful not to short to any other pin. the voltage on the drain should be around 325VDC
Then leave the negative probe on the cap negative and check EACH of the ic pins
Pin1=
pin2=
pin3=
pin4=
pin5=
pin6=
pin7=
pin8=Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
all clear, let's hope my hands don't shake, I'll do the test and let you know
Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
When checking the ic voltages just follow the trace from the pin and check the voltage on the next closest component, that way there is less of a chance of shorting.Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
voltage between capacitor and drain 315 volts
Pin1 = 0
Pin2 = 0
Pin3 = 0
Pin4 = 0
Pin5 = 0
Pin6 = 0.08
Pin7 = 0
Pin8 = 0Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
i've 8,2 volts, the capacitor is 47uf-35 voltsComment
-
Re: Dual output power supply 5 and 12 volts (no output)
forgive me I had left the tester set to test the big capacitor with the drain, here are the updated results
Pin1=0,47
Pin2=0,18
Pin3=0,35
Pin4=0,58
Pin5=0,87
Pin6=8,20
Pin7=0,03
Pin8=0Comment
-
Re: Doppio alimentatore in uscita da 5 e 12 volt (nessuna uscita)
I can check, it's one of the ones I replaced first, I also check the diode but I had already done it and it was goodLast edited by falcontech; 02-01-2021, 02:04 PM.Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
Your pin voltages are wrong. are you sure pin 6 has 8.2v and not pin7?Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
yes there is an error I inverted the pins, working with the ic on the contrary I made a bit of a mess ...
Pin5=0
Pin6=0,03
Pin7=8,20
Pin8=0,87
others are rightComment
-
Re: Dual output power supply 5 and 12 volts (no output)
Check the resistance of pin8 (ref) to pin5(ground) Pin 8 should have +5 volts if the ic is working, If the pin is not shorted or very low resistance to ground, check the output pins of the optocoupler to see if they are shorted. if not I suspect the ic is bad.
If you look at the datasheet you will see that the VCC pin supplies the 5v reference, so with 8.x volts on the vcc pin, the ref should be there as well.
Also check the winding of the transformer (marked in yellow) it should read less than 1ΩLast edited by R_J; 02-01-2021, 02:50 PM.Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
so in summary, I have to test if between pin 5 and pin 8 of the IC there are 5volts, I had already tested the optocoupler, I tested the output as a diode test, but it didn't mark anything, is it right or did I have to have some value? and then the transformerComment
-
Re: Dual output power supply 5 and 12 volts (no output)
I did the tests you asked me, between pins 5 and 8 I have 0,89 volts, the winding of the transformer that I tested without power is 0.01ohmComment
-
Re: Dual output power supply 5 and 12 volts (no output)
It's all getting very strange, what could I see again?Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
I wanted to tell you that I have another one working, could I do some tests?Comment
-
Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
That would likely not effect the ic's operation, it would cause a problem once the power supply started and would likely just blow the 47Ω resistor.Comment
-
Re: Dual output power supply 5 and 12 volts (no output)
It could be possible that zener diode connected to the vcc line is bad. It could check like a regular diode but be zenering at too low a voltage.
Since you have another power supply, compare the resistance of the ic pins to ground and see id there is a differenceLast edited by R_J; 02-02-2021, 11:02 AM.Comment
Related Topics
Collapse
-
by sam_sam_samI have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump
One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy... -
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?by Tynan DillI was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming...7 Photos -
by CMCMHello Everybody,
Trying to repair a power supply from a Russound CA4 Multizone Controller (picture attached)
Russound no longer supports it but were kind enough to provide a schematic of the power supply (pdf attached).
The outputs marked 12v and 20v are all measuring only 1v.
The board is clicking, which I think means it is in something called hiccup mode when the flyback transformers switches because of an internal problem or something else on the board Overloading it.
The capacitors physically look clean (no bludgesor leaks) and... -
by Gust zhangI have a 15 - inch Retina MacBook Pro from the mid - 2014 model. Here is the link: https://www.badcaps.net/forum/showth...light=820-3662 . The battery broke some time ago. After I removed the battery and plugged in the original power adapter, the MBP could boot up normally. However, when I checked with IntelPowerGadget, I found that the CPU speed was limited to 0.8 GHz, and it ran very slowly. Later, I found a solution on GitHub. There is an open - source project called cputune that can set the CPU running speed. So I can now run the MBP at full speed. But another problem...
-
by shamsudeenHi all, I just need to know that, can i use SMPS type power supply to test and short circuit detection on a laptop motherboard?
I saw 95% of repair guys are using only Linear bench power supply. linear bench power supply is pricy, thats why i planned to get one SMPS supply.
i know that in linear power supply the noise will be very low comparing to SMPS supply.... - Loading...
- No more items.
Comment