falcontech
Badcaps Veteran
Last Activity: 01-28-2025, 07:23 AM
Joined: 10-08-2013
Location: Reggio Calabria
-
What do you recommend? Can I do some tests? -
MOTU TRAVELER MK3 AUDIO PROBLEM
Good Afternoon
I have a problem with this MOTU audio card, a traveler MK3, the connection to the computer is via firewire, the card is recognized by the computer (both mac and win) but I have no audio output, on the front there are a series of LEDs including the clock (44.1, 48, etc.) and that LED at the time of connection usually remains fixed telling me the clock frequency set on the computer, now at every start the LED in question remains flashing in most cases, sometimes it becomes fixed, other times it disappears, without any sign of operation, I exclude problems with the firewire chip,...Last edited by falcontech; 01-24-2025, 10:24 AM. -
Yamaha Msr400 Input Board Problem
Good morning everyone
I have a problem with this input module of an active speaker of the Yamaha (MSR400), the signal transmitted by this unit and sent after the EQ module and then end up the amplification form is lower than normal, I attribute the problem to this Module because with that of the twin box works perfectly, I thought of the three capacitors highlighted in the photos and that I have not yet replaced or the operational highlighted NJM2860L, the strange thing I noticed that by trying with the jack by pulling it a little out of the normal position the earnings is normal, while... -
Re: Aiwa ad-wx 717 belt measure
the problem is that it is in an awkward position, to have all the thread you are talking about I have to close the mechanism where the motor and its pulley are located, at which point I can no longer even put my hands in it to pass the thread, the mechanism it opens in 2 parts, in one I have two pulleys, in the other there is the motor with another pulley...Leave a comment:
-
Re: Aiwa ad-wx 717 belt measure
I saw that there is the kit but not the measures...Leave a comment:
-
Aiwa ad-wx 717 belt measure
Hello
Could someone tell me what size the drive belt of the aiwa ad-wx717 cassette deck is, I would like to buy it independently in my trusted shop, there is a kit online but I find the price exaggerated, unfortunately the original has practically melted. it is a double plate and the belts are the same, the one of the tachometer has remained intact thanks -
Re: Epson EB-S03 Hdmi Problem
And so?Leave a comment:
-
Re: Epson EB-S03 Hdmi Problem
The vga workingLeave a comment:
-
Re: Epson EB-S03 Hdmi Problem
this is the eeprom...Leave a comment:
-
Epson EB-S03 Hdmi Problem
Good afternoon
I have the hdmi input of an Epson EB-S03 projector that does not work, in the attached photos there is the card which is a H550M_R1, I read somewhere that replacing the eprom circled in red solves the problem and among others things does not need software, just replace it, the eprom is a tssop 24c02, has anyone ever dealt with this type of repair? Thank you... -
Re: Numark NS6 Usb problem
I haven't been able to find a card yet, if you write me a month later it's hard to come to a conclusion...Leave a comment:
-
Re: Pioneer Xdj-rx
Sorry 4580d...Leave a comment:
-
Re: Numark NS6 Usb problem
the card is this, let me know if it is working and how much you would like to make...Leave a comment:
-
Re: Numark NS6 Usb problem
I had already looked on leboncoin but it does not allow me to register if I am not French, also before doing this operation I must be sure that the problem is only the usb port to be replaced, if not I am buying another scrap of which I will not know what let me know, let me have more precise information or in any case leave me your direct contact even in private thanks that you are interested...Leave a comment:
-
Re: Numark NS6 Usb problem
hello this is the card, could we agree where you are from? I need it sent...Leave a comment:
-
Pioneer Xdj-rx
Hello
Today I am struggling with a controller for dj xdj-rx, I have a low volume on the main output of the master compared to the booth, both should have + 6db output but the difference is heard enough, I saw that on the board where the various outputs the master is driven by 2 njm4850d, could they be the problem? thanks to those who can help me, I do not have an oscilloscope, I cannot attach the service manual because it is too heavy if it were to be needed I have one -
Re: Numark NS6 Usb problem
This is not the main boardLeave a comment:
-
Re: Problem transfer file from a samsung sgh-e710
where would this memory card be found? do i have to take the phone apart?...Leave a comment:
-
Re: Problem transfer file from a samsung sgh-e710
the download takes me to a page where it asks for a login and there is no possibility to register I had already seen this download and all the others lead to this HAMA page...Leave a comment:
-
Problem transfer file from a samsung sgh-e710
Good morning everyone
I need your help because I have to recover photos from an old samsung sgh-e710, the cell phone has only infrared to communicate with the computer and the usb cable (purchased for this reason). I have downloaded both PcStudio 3 and Easy studio but I cannot show him the phone, I probably need the drivers that I cannot find online, currently I have tried with windows 10, but if it is necessary I can install windows xp on a computer, I await the your help thanks
No activity results to display
Leave a comment: