thinkbook 14,15 g4 iap bios bin NEED

[mferna14]

I matched the BIN before programming... Header was 100% same on both but in the middle the DATA was different. You did it very well & the BIOS even was read perfectly. For where did you get the FF FF photo, in the start it was all yy on both???? We are using the RT809H programmer, the program gives the right match for the chip with voltage. This is a 1.8V chip 256KB. Thanks

[bsloboda]

I matched the BIN before programming... Header was 100% same on both but in the middle the DATA was different. You did it very well & the BIOS even was read perfectly. For where did you get the FF FF photo, in the start it was all yy on both???? We are using the RT809H programmer, the program gives the right match for the chip with voltage. This is a 1.8V chip 256KB. Thanks

I used Neoprogramer 2.2.0.10. and CH341 flasher I2C protocol socket. Just 2 days ago I ordered SOP8 DIP8 connectors and 1,8V adapter, hoping that I would flash the BIOS chip of this laptop, thinking that the BIOS chip is 1,8V supplied. According to boardview the BIOS chip was supplied with 3,3 V, I also measured with multimeter right on the motherboard and the supply voltage was 3,3V, datasheet says supply voltage 1,8 - 5,5V. The same is with the U15 chip, I checked datasheet and range is 1,8 - 5,5V. On boardview the supply voltage for PD controller memory is 3,3 Volts. Neoprogrammer recognized the chip as 3,3V so I proceded with that voltage. Anyways, I am happy for You, that the laptop is ON again.

Link to schematic - https://www.badcaps.net/forum/troubl...and-schematics

[mferna14]

I used Neoprogramer 2.2.0.10. and CH341 flasher I2C protocol socket. Just 2 days ago I ordered SOP8 DIP8 connectors and 1,8V adapter, hoping that I would flash the BIOS chip of this laptop, thinking that the BIOS chip is 1,8V supplied. According to boardview the BIOS chip was supplied with 3,3 V, I also measured with multimeter right on the motherboard and the supply voltage was 3,3V, datasheet says supply voltage 1,8 - 5,5V. The same is with the U15 chip, I checked datasheet and range is 1,8 - 5,5V. On boardview the supply voltage for PD controller memory is 3,3 Volts. Neoprogrammer recognized the chip as 3,3V so I proceded with that voltage. Anyways, I am happy for You, that the laptop is ON again.

Thank you very much dear for all the help!!! & the Schematics & Boardview, Admin pls. move the schematics/Boardview to the right location., Thanks

[SMDFlea]

Thanks, schematics link added .

[reaper422]

Customer feedback while updating bios the machine turned off.
When you press the power button, the machine runs for 5 seconds and then turns off.
Сould someone help me repairing my original dump?
Thanks in advance.

device:Laptop
brand :LENOVO
Model :THINKBOOK 15 g4 iap
Board no:LA-L931P ,rev1.0
S/N: MP2ЕЕЗ63

[hoaca388]

Customer feedback while updating bios the machine turned off.
When you press the power button, the machine runs for 5 seconds and then turns off.
Сould someone help me repairing my original dump?
Thanks in advance.

device:Laptop
brand :LENOVO
Model :THINKBOOK 15 g4 iap
Board no:LA-L931P ,rev1.0
S/N: MP2ЕЕЗ63

ThinkBook 15 G4 IAP - Type 21DJ

[gsm_code]

Help unlock pls
thinkbook 14 G4 iap
sn: mp29km1f
LA-L931P rev: 1 .0

[gsm_code]

Up pls

[shiyab]

Help unlock pls
thinkbook 14 G4 iap
sn: mp29km1f
LA-L931P rev: 1 .0

hi try feedback

[gsm_code]

hi try feedback

Password not remove

[shiyab]

Password not remove

HI try

[gsm_code]

HI try

Tnx for helping, its working now no bios password

[xpy000]

Hi
Can you please help me remove password from this bin file
thinkbook 14 GA iap
SN MP2JWLM
Board ID LA-L931P

[danito]

Hi
Can you please help me remove password from this bin file
thinkbook 14 GA iap
SN MP2JWLM
Board ID LA-L931P

try and SN is MP2FJWLM not MP2JWLM

[xpy000]

Hi danito. Thanks for your help. I really appreciate it. After flashing your unlocked file the computer won’t turn on.(the power button lights up for a couple of seconds and then it turns off. The computer seems to be charging the battery just fine) I tried one of the files shared by one of the guys on this post. The computer turned on fine but hard drive is not detected obviously because the bin file I flashed is for 15 model and mine is 14. Could you please advise as to what I should do next. Thanks

[piszpunta]

Hi danito. Thanks for your help. I really appreciate it. After flashing your unlocked file the computer won’t turn on.(the power button lights up for a couple of seconds and then it turns off. The computer seems to be charging the battery just fine) I tried one of the files shared by one of the guys on this post. The computer turned on fine but hard drive is not detected obviously because the bin file I flashed is for 15 model and mine is 14. Could you please advise as to what I should do next. Thanks

try

[volinakis]

try

danito, piszpunta - his bios backup is faulty. look how it ends and the size.

[volinakis]

Hi danito. Thanks for your help. I really appreciate it. After flashing your unlocked file the computer won’t turn on.(the power button lights up for a couple of seconds and then it turns off. The computer seems to be charging the battery just fine) I tried one of the files shared by one of the guys on this post. The computer turned on fine but hard drive is not detected obviously because the bin file I flashed is for 15 model and mine is 14. Could you please advise as to what I should do next. Thanks

your bios backup is faulty. Try this file. (ssd is not detected "obviously because the bin file I flashed is for 15 model" , it's because of intel ME)