A1706 820-00239 u3100 #52 solder pad lost

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • liteott
    Member
    • Mar 2012
    • 23
    • usa
    #1

    A1706 820-00239 u3100 #52 solder pad lost

    Try to Replace U3100 (CD3215C00 chip) it was pad #62 ppbus_g3hot short to Ground (CB300 take out still short) after remove off the U3100 "short" disappear.
    But for maybe temperature not enough high I found the solder pad #6 #50 #52 was lost and the #6 and #50 are GND I don't care but the #52 shows
    "NC_USBC_XA_RESET_L" and I want to see where this point to go or come but the board view shows no-where to go or come.
    Can you help me what this" NC_USBC_XA_RESET_L" to do and if I replace new ic chip without this #52 pad should the board working? (I already change two times and not work: the power meter go black nothing I don't know if it's bad soldering work or this #52 pad missed.(maybe it was bad soldering because under the ic chip there a thick glue layer before I didn't clean maybe some pad point not making contacted.
    and if it is #52 pad lost problem how can I resolve it
    Attached it the board view and schematic. many thanks.
    Attached Files
    Tags: None
    • Harryrepair
      Senior Member
      • Jul 2016
      • 69
      • Germany
      #2
      Re: A1706 820-00239 u3100 #52 solder pad lost

      NC means not connected, you can solder the chip on without pad #52

        Comment

        Previous template Next

        Related Topics

        Collapse
        • corrize
          Best way to solder LVDS connector for beginner (and qfn) ?
          by corrize
          Hello, I'm a beginner for micro soldering. Right now I have some difficult to solder a qfn 20, I guess I put too much solder on the thermal-ground pad, the result is a corner of chip wich don't touch the board (last try).

          I use a wire solder with hot air, I tin the board and chip before with iron and I use good flux.

          I will have to solder a LVDS connector (40 pins, laptop pc), I saw a solder paste in seringe, good quality (it does not scatter).
          See the test :
          https://youtu.be/bNAzC-EvqHs?t=1767

          With hot air from bellow the board, that's...
          03-09-2023, 02:57 AM
        • francescoranchi
          MBP 13inch 2018 No Power - 820-00850-07 motherboard faulty (U3100 get's hot)
          by francescoranchi
          Hello everyone! I'm new to this forum but I hope I can find help and also help others at the same time!

          I have a MacBook Pro 13inch from 2018 and it doesn't turn on anymore it's completely gone. I was using it connected to a USB-C / HDMI adapter to connect it to the tv when it just turned off and it's not powering on anymore.

          I don't have an AMP meter so I can't see how many amps are getting pulled. The only symptom is the U3100 getting very hot, upon closer inspection it looks like it burned because there's a small hole on the top surface of the IC (I've already seen...
          09-16-2023, 07:08 AM
        • myth77
          UV solder mask - high temp resistent, recomendation?
          by myth77
          Can someone recommend any good UV solder mask? But i need a solder mask that will stand high temperetures. The thing is...sometimes i have a bigger cooper ripped from the board, lets say mosfet pad... i reconstract it with cooper sheet, then i "glue it" with solder mask...then i use UV light...and let it cool a bit. After, i try to clean the cooper of extra solder mask..and till that part all is ok. But, when i use a soldering iron to solder that pad/cooper...the solder mask gets weaker or destroyed and finally the pad is ripped again from the board .
          Is there any solder mask...
          03-28-2022, 04:04 AM
        • petemanuk
          BGA solder balls not connecting - help pls
          by petemanuk
          So I though in my spare time I’d set myself up repairing motherboards mainly pin damaged lga1151 sockets types.

          I’m using an achi ir sc pro rework station (gave up on my Achie ir6500 - don’t recommend)

          I’ve managed to get my rework profile somewhere in the correct region (after a lot of trial and error) to get the old sockets off and reflow new ones back on again, the problems I’m getting is not all of the solder balls are re-attaching when re-flow occurs. I know this because when socket is removed pads still look clean and have no solder...
          11-16-2022, 05:21 AM
        • acedogblast
          Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
          by acedogblast
          This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

          There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
          11-02-2024, 05:13 PM
        • Loading...
        • No more items.
        Working...