Hi i have a question those anyone is using this type of programmer?
bECUASE I Dont have any idea how to use this
bECUASE I Dont have any idea how to use this
-
-
Re: I.O programmer SAS JIG 3.8V
Sound like a vertyanov clone,
What type of chip you want programm ? -
Re: I.O programmer SAS JIG 3.8V
It is a clone. Good luck getting software updates for it
Comment
-
Re: I.O programmer SAS JIG 3.8V
Don't buy it! I thought I was buying the original one, seller is ioprogrammer in Ebay, now programmer needs to be reprogrammed and he's not providing dump to fix it.Comment
-
Re: I.O programmer SAS JIG 3.8V
Report it on Ebay for counterfeit.Comment
-
Re: I.O programmer SAS JIG 3.8V
Well, I have it and they do seem to update it regularly... I don't have too much use for it tho. Only had to program ITE SIO chips and it has worked well thus far.Comment
-
Re: I.O programmer SAS JIG 3.8V
I use it to test keyboards and sometimes flash KBC. Can you dump the ATMEL FW?Comment
-
Re: I.O programmer SAS JIG 3.8V
The genuine vertyanov jig now has to be registered,it was done to stop the clones. Sergey vertyanov said in the russian forums he should have protected the software from the start. The clones have been using his software. When he made that change there were some accusations on vina about the latest software having a virus/trojan, which isn`t true, obviously the cloners were upset .I don`t know what happens if you try to update the software on a clone,does it brick it ?Comment
-
Re: I.O programmer SAS JIG 3.8V
Now that you mention it, I recall the software was asking me to update the FW, now it doesn't stop beeping and if I use vertyanov official software, it's able to update to new FW but it's telling me I'm using a clone.
How is the protection being done now? Is there a blacklist? Can we pay to add our devices to whitelist?Last edited by orientalsniper; 11-26-2019, 03:26 AM.Comment
-
Re: I.O programmer SAS JIG 3.8V
When i said at post #3 good luck getting software updates i thought it would just block you from getting any updates, so youve confirmed it does actually brick it if you update the FW .I`m not sure if you could flash the firmware dump from another clone.It may be your only way to unbrick it, then use older software versions ?Comment
-
Re: I.O programmer SAS JIG 3.8V
I also use maybe clone made in turkey 2017 working well.When i use new model like NUVOTON not support and contact he said send me i solve free or change Atmel also free..Comment
-
Re: I.O programmer SAS JIG 3.8V
Considering the authentic is the same price as the clone, I don't see why anyone would choose the clone?
Vertyanov should have sold it in Ebay to prevent clueless buyers.Comment
-
Comment
-
Re: I.O programmer SAS JIG 3.8V
Because it was easier to buy the clone for a company.Comment
-
Re: I.O programmer SAS JIG 3.8V
Its working very well and regularly being updated without any problem besides it has its own name "sas jig 3.8v".i found many videos on youtube as wellComment
-
Re: I.O programmer SAS JIG 3.8V
I don' trust it, for the same price just get the original, updates will stop if vertyanovis going to add protection.Comment
-
Re: I.O programmer SAS JIG 3.8V
Vertyanov told me, it's this one:
https://www.ebay.com/itm/Sergey-Vert...oAAOSwF0NcN3R-Comment
-
Greetings badcaps community,
I havent done this for a long time and want to start it all again, after some evil and annyoing illness.
So I apologize in advance, if some phrases might sound a bit like gibberish or illogical to you.
Im trying my best to fully describe what I plan to achieve and hope I was choosing the right sub-forum for my new adventure.
I have a Elitebook 820 G1 and a Elitebook 840 G2 here.
These ask for a password when entering the BIOS, but boot just fine from the internal SSD.
I learned that desoldering...10-29-2024, 06:03 AM -
Recently I've gotten into EC flashing due to my broken laptop(s) and started frantically searching methods for flashing the IT5571E-128 chip on the cheap(due to me beaing a student and not having a job) and noticed that ITE newer chips can be flashed via ISP (In-System Programming) either via SMBus or the KBC (EPP - Enhanced Parallel Port) interface. While these can be achieved with programmers like SVOD4/3 or the RT809H/F those options are WAYYY out of my budget so I was horrified. But recently I stumbled uppon some programmers on aliexpress that claim they can program a variety of ITE chips...06-17-2025, 07:17 AM
-
- Dell Latitude e5580
- SN: D01JGH2
- MB: CDM80 LA-E091P Rev: 2.0 (A01)
- SPI: 25B128CSIG
I had problem with this laptop that in post it was giving TPM is missing warning. There was no TPM option in BIOS, I`ve tried all Windows/BIOS methods with no luck. I tried to downgrade BIOS thru Windows but Dell have disabled this option so I came up with the idea changing SPI firmware by programmer.
I`m using CH341 one, I`v started with the software that was provided with the programmer. It was reading my chip as:
- 25/26 SPI
- Dell Latitude e5580
-
Hi has anyone got the latest software for the TL866CS MiniPro EPROM programmer version 03.2.86 is installed now i have tried the update site in the programmer software but it wont connect to their website i am running windows 10
Edit found this site programmer works now http://www.xgecu.com/EN/Index.html -
Looking to up my game a little bit, but these programmers seem a bit daunting.
Trying to get a device for EMMC repair, and it's very difficult to lookup all the words to find if I'm on the right track lol.
Trying to reprogram EMMC on Sony/Hisense mainly but would like to hit a few other brands.
My question is would either of these work? And is there a specific card reader I need for TV emmc? There is like 10-40 additional pieces that I can get but not sure what I actually need for my application only.
I may do eeprom as well. Can someone point...
Comment