Hello, I have a problem with starting my laptop. I got a laptop that doesn't start. It turned out that it was flooded with liquid. I removed the corrosion, replaced the damaged elements and the laptop started. Before I understood what the problem was, I uploaded a new BIOS with a clean ME region downloaded from this forum. The laptop started and worked. However, I decided to upload the original BIOS back. I cleared the ME REGION in it and uploaded it to the chip. After this procedure, the laptop stopped starting. It uses 6 watts constantly without any changes. Also, uploading back the BIOS with which it started after repair doesn't help. Is it possible the KBC chip is bricked? I don't have a programmer for KBC systems. Do you have any ideas? Thanks!
-
-
KBC firmware is unlikely to be corrupt. Check whether chip is properly soldered and do check for any missing resistors nearby. -
I have checked this before. Everything with resistors and capasitors is fine. Like I said before flashing it was working properly. So i need to find a way to flash KBC it seems...Comment
-
Is the EC rom internal or external on this board? My database shows a dump for this model which I can post if needed.
Comment
-
Post the original bios backup in the bios requests forum - https://www.badcaps.net/forum/troubl...-requests-only ,and post the laptop serial number (type it please) ,and also post a picture of the barcode sticker on the ram slotComment
-
Wait on others to comment but from this video, the EC ROM chip is an external part. That is, the EC controller = KB9026Q is the controller and it uses the external Winbond chip to hold the firmware (program). If indeed, this external flash device is corrupted, then a known good EC rom dump should be suitable to apply onto this target flash chip.
https://www.youtube.com/watch?v=CgDV2oxQhsI
This YT video is using the u-Link NT Programming tool and from a quick Aliexpress search, someone is attempting to gouge the buyer @ $3k for this device worth about $5. Suspecting there are many options to reflash this target memory device including the option to remove this flash chip -> program with the device with a low cost tool and then solder it back.
Confirm if you have this flash device on your board like showing in the video when he flips the board over.Comment
-
Once again i'm saying its not EC bios. EC has a separate flash chip and the ec bios is not pulled from main bios in this case.
Since you only flashed main bios, it has nothing to do with ec bios.
Rather, look carefully at liquid spill area and you may get a clue.Comment
-
With ASUS, not everything is quite so simple. I will show you my way. It may be longer or harder but it is the right way to do it in my humble opinion.
For example, you can have 3 similar ASUS motherboards, all being the same model, all of which will have different BIOS versions.
I will give you an example and my version of preparing BIOS from ASUS website and in the process I am always cleaning Intel ME while doing it so you have fully cleaned BIOS, no DMI data, no password, nothing.
This is the picture of 3 similar ASUS motherboards, all of them being X555LD... -
ASUS ROG Ally X - (Handheld Gaming PC)
Model No: RC72LA
Serial No: SBNVKD001014459
Hi all, I've spent the past week digging through the forums and guides to try correct my foolish mistake of changing hidden settings while tinkering around, and to be honest my heads overloaded so I'm hoping you'll be able to help.
I used a tool called 'Smokeless-UMAF' to access usually hidden settings in the bios. I tweaked one or two 'safe' things but made the mistake of tweaking a lot of settings under 'USB/Thunderbolt Configurations' when I didn't know what they did. For... -
Hi, my laptop wont boot at all
With original bios no POST, only LED lights
With alternative BIOS from model TP500LN (flashed via programmer) the notebook works again
Some issues
A- with bios from 500LN, it won't update from bios of model 500LA (from 500LN v203 to 500LA v300)
B- If updated from 500LN version 203 to 300, the battery stops being recognized
Things I tried
1- Update / clear ME: Took the non working bios, made a backup, and did this: https://www.badcaps.net/forum/troubl...theory/trouble... -
Hi,
I have a serious problem to program the Z590 chipset SRAM with a Management Engine after replacing the chipset.
The new chipset is factory new and is not containing any Management Engine. Any attempts to program it into the chipset under Windows ends with a failure (eg. Error 20: Management Engine Device not present, or something similar).
Due to the lack of the ME several ports on the board, including all M.2 ports aren't working, booting OS works only on USB. So it's now other way, as to program the chipset with a ME.
Usually on ASUS boards it worked... -
hey all, i did a silly thing and flashed bios to perfectly working board. None of the asus official download bios would work with ez flash. They all gave error saying not supported bios file. I tried using uefi tool to extract it to a bin file but then ez flash wouldnt even recognise it.
So, i used freedos and afudos with the aforementioned bin file i extracted and forced the issue. After bios reprogram, reboot and it was dead. Fans spinning but no post.
i have a bios writer and none of the .cap files from the official site work either. I just get one spin, then off, then all fans...10-17-2024, 02:53 AM
Comment