DV2000 no light on screen

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • marcellodj
    Senior Member
    • Nov 2010
    • 99
    #21
    Re: DV2000 no light on screen

    @kiranfocuz:
    150c is not enough to reflow pbfree soldered bga; reflow come at 217/230 , and you need prebake,preheat the board and so on..without after a couple of days the unit will return on your bench..see literature.
    Last edited by marcellodj; 06-07-2011, 03:23 PM. Reason: addenda

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • mmccomputer
        problem with replacing lcd screen
        by mmccomputer
        I have an HP model : 14-cf0011nf and I want to change its display screen (it has an original 14" full HD TN 30 pins panel) which works without problem but I want to put another screen with an IPS panel, the problem is that I tried several screens but there is no display except with the original screen, I never had this problem before I changed hundreds without problems but this PC is not 'accepted than its original screen
        otherwise on the motherboard it displays edp and I don't know, do the panels I tried only work with the LVDS protocol?
        If anyone has any information on the subject...
        12-15-2024, 03:44 PM
      • jimjoe123
        LCD TV Green/Pink screen problem
        by jimjoe123
        I have a Dick Smith 37" LCD TV, Model GE6804. I am using it as PC extended monitor only.

        Problem is while watching tv, I hear a semi loud click(like a electrical breaker tripping due to overload, just sound like it but no actual electrical overload), then screen is covered with green or pink. I can still see the original picture image but overlayed by green or pink. See attached images. Pink.jpg is what I see, and Normal.jpg is before green or pink screen, What I captured was pink screen, but about 80% of time it's green and 20% of time it's pink.

        Then each time...
        02-23-2020, 01:29 AM
      • howardc64
        A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
        by howardc64
        Problem

        This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
        08-04-2024, 10:36 PM
      • Chrissygizmo
        Sony KD-55XG9505 lines on screen problem
        by Chrissygizmo
        Hello again everyone,

        This is my latest mission, to try getting this Sony tv back to normal working order…

        I've only just got it today, when you power it up everything is as should be, in fact it works perfectly for a few minutes then the screen starts getting horizontal lines on & eventually the full screen goes back, I will upload photos of the problem & also some photos of the board etc. You might notice that I'm busy trying the tape method, I'm not sure exactly where the clock lines are so I'm just guessing & hoping for the best lol . I've already tried...
        02-19-2025, 11:31 AM
      • Rav_tangle
        MacBook Pro 2011 turns on with keyboard light , screen dead
        by Rav_tangle
        Hi all , thanks for having me & I think this has been asked before but my case seems a bit odd.
        I have a MacBook Pro , board 820-2915a and it turns on , chimes etc etc , keyboard lights up, fans spins , can turn caps lock on/off but screen is dead.
        Iv tried the resets , shine torch through back logo , nothing , it seems the screen has no power. If I plug charger , it charges but if I disconnect battery it displays green light but won't turn on. Iv tried screen on with another board & it works & seems I'm not getting any voltage at pin 2 , next to ground pin .
        is this...
        05-31-2024, 04:09 PM
      • Loading...
      • No more items.
      Working...