Unowhy Y13 . I have to unplug the battery connector before flashing the bios. But I can't remove this connector and I pulled hard but it doesn't disconnect. I'm afraid to break it. Is there a special way to remove it? THANKS
-
-
Re: Help Unowhy Y13 Remove battery connector
pictures please -
Re: Help Unowhy Y13 Remove battery connector
This is the photo.I can't disconnect it. Thank youAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: Help Unowhy Y13 Remove battery connector
You have to pull see the arrow directionAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: Help Unowhy Y13 Remove battery connector
I pulled several times according to the arrows and sometimes very hard at the risk of tearing it from the motherboard, but it does not come off. there must be a locking system. It's stupid but I don't see how to disconnect it.Comment
-
Re: Help Unowhy Y13 Remove battery connector
that's ok . Thank you for your helpComment
-
Re: Help Unowhy Y13 Remove battery connector
For sure there is no lock, look at this video:
https://www.youtube.com/watch?v=wQ-q3Ct9go4Comment
-
Re: Help Unowhy Y13 Remove battery connector
like thisAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: Help Unowhy Y13 Remove battery connector
Thank you for your help. Problem solvedComment
-
Hi Gang, Im working on Macbook Pro A1990, the battery connector was torn off during friend trying to replace battery. I soldered on the connector back, and created traces. The battery does charge (according to amp meter), and does power on battery only. But the signal detect line maybe done incorrectly, and the macbook shows "X" over battery icon, and "Service Recommended" on new battery
Can somebody point me to which of these connector pins is responsible for battery detect/data line? Pin 4 on schematic had a nub on the trace, im not sure if that is important,... -
Hello everyone,
Mark and model: ASUS X571
Symptoms: not turning on. There is only the LED battery indicator working. The owner of the laptop told me this problem arrived one week after having changed the battery. He then managed to power on the laptop only once, and then it never powered on again.
Tests already made:
- Battery is charging when laptop is plugged in. The LED battery indicator turns white after a couple of hours of charge, indicating that battery is fully charged. However, laptop won't turn on anyway, with or without AC plug.
- I have removed... -
Problem
This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached.... -
I bought a Vostro 3400 motherboard (LA-K033P) to upgrade over my damaged Inspiron 5593 (LA-J091P) board. Everything else is ok except for the battery. This battery I am using now is already a replacement one since I disposed of the bloated original one. Back in the Inspiron 5593 motherboard, the battery charges fine and is identified just fine. However, with the upgraded motherboard, suddenly the replacement battery is labeled as "Not a dell battery". When I borrow a similar battery from my colleague (which did not have replacements yet), it is identified and charges just fine.
... -
The ISL88739 & ISL88739AHRZ are a highly versatile combo battery charger
configurable for operating as either a Hybrid Power Boost (HPB)
charger or a Narrow VDC (NVDC) charger, supporting 2-, 3-, or
4-cell batteries. Both configurations allow the battery to work with
the adapter together to supply the system load when it exceeds
the adapter capability, referred to as system Turbo mode. HPB
charger configuration reverse-boosts battery energy to the system
bus to help the adapter provide the system power in Turbo mode.
NVDC charger configuration...11-05-2024, 03:28 PM
Comment