Philips sunmobil HP3132/B sunbed xformer and cap shot

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • notallbad
    Badcaps Legend
    • Oct 2012
    • 1190
    • UK
    #21
    Re: Philips sunmobil HP3132/B sunbed xformer and cap shot

    Originally posted by stj
    damn - have to see how much it weigh's to see how much the post office will fuck me!
    actually i should dig it out and check the size first.
    it came from a 48w soldering station.
    I appreciate your help and the kind offer but suspect postage costs would have been too much.
    The good news is the sunbed is working again at not too great of a cost, I picked it up free and very happy to have it working. Time to get tanned!

      Comment

      • stj
        Great Sage 齊天大聖
        • Dec 2009
        • 31293
        • Albion
        #22
        Re: Philips sunmobil HP3132/B sunbed xformer and cap shot

        fair enough.
        i dont know why they have 24v in the 858d - maybe they just used the transformer they already had for the soldering stations

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • Sharpa
            Repair attempt Philips 55OLED804/12
            by Sharpa
            Hello,

            I bought a SH Philips 55OLED804/12 TV with known defect in an attempt to repair it for personal use.

            The symptoms when bought: Philips logo appears then tv turns off

            Things tried so far:

            1. Powering it on: Philips logo shows on the screen, sometimes with some minor artefacts then shuts down. Red status led flickers rapidly into two batches then repeats
            2. Put it in recovery mode by pressing joystick down then plugging it to mains: The tv shows the logo then shows the android animation along with some minor artefacts on the screen...
            Yesterday, 08:30 AM
          • alro7779
            Philips 32PFL4901/F8 BA4GF0F0102 2 Not getting standby led
            by alro7779
            Hello, guys!

            The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601...
            09-14-2025, 12:25 AM
          • G33RT
            Philips 8200 series 65PUS8204/12 stuck at Philips Logo
            by G33RT
            Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.

            It does power up when pressing the power button.

            I already try the power button while plugin the plug with no result.
            Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.

            Could this be an PSU or eMMC issue ?
            07-19-2025, 03:43 AM
          • double_DD
            Philips curling iron - is this a common AC cable?
            by double_DD
            Hi all,

            Wife has 2 Philips hair curling irons half defective - after learning how they're supposed to work and testing them, it turned out that both have defective power cables, and both on the same place; broken wires due to wire bending.
            As they were both relatively easy to disassemble, and cables are plugged not soldered (as they can rotate in the handle), I was sure it would be easy to find replacements. But - NO! I'm unable to find anything similar on ebay or Aliexpress.

            Not sure if this is something Philips proprietary, or a standard, but the cable plug...
            08-18-2025, 10:04 AM
          • janos6662000
            Philips 47PFS7509/12 LCD TV problem
            by janos6662000
            Hi

            I have here a Philips 47PFS7509/12 LCD TV which came to me with a weird problem : without signal i could access menu, make a factory reset, access menus, etc.
            When i applied cable signal to check image, i had normal picture, but TV was restarting.
            I downloaded original firmware and applied the update, but the problem remained.
            From a colleague i received a "factory package software" which is a lot bigger.
            I made another firmware update, but still did not solve the problem.
            Somewhere on the way the error got worse, because at the moment the...
            08-12-2025, 12:54 PM
          • Loading...
          • No more items.
          Working...