PS5 EDM-020 HDMI short on pin 19.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • AlexWhat
    Member
    • Mar 2024
    • 11
    • Canada

    #1

    PS5 EDM-020 HDMI short on pin 19.

    Any body knows where the pin 19 from HDMI trace goes to? it is shorted to ground.
    Update; short disappeared and was able to traced it to pin 46 of the Panasonic chip but first goes through 22-ohm resistor and another resistor and diode is attached to line and ground, my measurement of second resistor was 6.7k red probe on the line.
  • AlexWhat
    Member
    • Mar 2024
    • 11
    • Canada

    #2
    Added picture
    Attached Files

    if you find these attachements useful please consider making a small donation to the site

    Comment

    • LaPCon_IT
      Senior Member
      • Sep 2022
      • 82
      • Malta

      #3
      Short's gone, and? What the symptoms are?

      Comment

      • AlexWhat
        Member
        • Mar 2024
        • 11
        • Canada

        #4
        UART reading attached
        Attached Files

        if you find these attachements useful please consider making a small donation to the site

        Comment

        Related Topics

        Collapse

        • gaelican
          Asus ROG ga401IV motherboard - AC Short Protection resistor getting hot
          by gaelican
          Hi,

          I am working on an Asus ROG laptop repair. I was able to find that there is a short on the motherboard, and the 20 volts from the charger only gets to the first mosfet before disappearing.

          When looking around with a thermal camera, I noticed the chip marked "14C" in the picture was getting warm. Nothing else was receiving heat.

          I found a boardview diagram and schematic for a motherboard that looks nearly identical, that has the same component. This appears to be marked as "AC Short Protection" with a value of 13.7KOhms.

          ...
          02-21-2025, 01:51 PM
        • madyoyo
          Samsung eu58tu6928k - Short on CK3 line -
          by madyoyo
          Hello.
          I have a Samsung eu58tu6928k with the dreaded bootloop fault.
          No external tcon, one 96 pins ribbon between mainboard and the left side of the panel, and a ribbon to the right side.

          I narrowed the problem down to the CK03 line. When i isolate only this line on the ribbon joining the 2 halves of the panel, the tv boots, but the picture is quite bad. I also tested all MLCC caps on the panel, no short so far. Is there anything i can try before ruling the panel, and the whole tv as scrap?...
          11-05-2025, 04:55 AM
        • CapLeaker
          Happened again. Resistor go short!
          by CapLeaker
          That's now the second time in my repair career that a through hole resistor go short!
          it was a Vishay CPF124K900FHB14 1W resistor measuring new 24.9kohm. <- notice the KILO ohm. Well now it measures 28.1 Ohm! See picture and PDF attached. This is something very rare happening, but apparently it does happen!...
          07-07-2025, 03:20 PM
        • ktmmotocross
          HP Omen 17-an108nc - 3long and 2 short/memory error/ after capacitor short on 5V line
          by ktmmotocross
          Hello.
          I have this HP Omen 17-an108nc that show 3long and 2 short/memory error/ led blinks on Caps-lock after capacitor short on 5V line.

          Come with one shorted capacitor on 5V line. After replce it just blinks memory error. i flash main and EC bios but still the same. I have all voltages on start, cpu fan spining, but onli capslock blinks and no picture

          any hint?
          01-03-2023, 06:07 AM
        • fricosu007
          Macbook Pro M1 X A2484 820-02100 short on PPvin_5vusbc23 line
          by fricosu007
          Hello friends, today i got an A2485 820-02100-A in a desd state, found visual short on PPVIN_5VUSBC23 line, removed tantalum capacitor, installed same same value from other donor board, now there is no short on any of the rails but when i plug either magsafe3 or usbc inget 5v stable with 0.00 amps drown, no cycle, just these steady values, board is not in dfu mode, checked with magsafe and with usbc. Only value that i find on the board is ppdcin_aon which is 5v… i dont get 3,3 aon, 3v8 aon .. all missing, where should i start looking please !...
          05-10-2024, 09:40 AM
        • Loading...
        • No more items.
        Working...