Stress Test after Re-capping

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Ravenworks Computers
    New Member
    • Aug 2005
    • 1
    #1

    Stress Test after Re-capping

    Chris, I need to know if you fired this board up and ran it like you said you were going to, because it is dead and I need to know so I can order new one.
    I have already replaced the power supply, so I know that is not the problem.
    Tags: None
    • Topcat
      The Boss Stooge
      • Oct 2003
      • 16956
      • United States
      #2
      Re: Stress Test after Re-capping

      As I told you in the email, YES. It passed with no issues.
      <--- Badcaps.net Founder

      Badcaps.net Services:

      Motherboard Repair Services
      ----------------------------------------------
      Badcaps.net Forum Members Folding Team
      http://folding.stanford.edu/
      Team : 49813
      Join in!!
      Team Stats

        Comment

        • kc8adu
          Super Moderator
          • Nov 2003
          • 8832
          • U.S.A!
          #3
          Re: Stress Test after Re-capping

          this is why i prefer the customer to send the ram and cpu that was in the system.
          these parts also get the benefit of the test.

            Comment

            Previous template Next

            Related Topics

            Collapse
            • Inforgalaxie
              Overheating in Stress Test
              by Inforgalaxie
              Hello i have a problem, i have a laptopt Dell E5570 that in stress test without the battery it works good and not turn off.
              But when i conect the battery and made a stress test the cpu temperature go to 95º and turn off. I also was testing with a new battery and the problem is the same in stress test turn off with big cpu temperature (95-100º). What can be this?
              12-13-2023, 03:24 AM
            • chth96
              How Can I test PWM DM0365R?
              by chth96
              Hello
              I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
              So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
              I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
              I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
              06-18-2025, 04:14 PM
            • khelane
              test active pfc power with lamp test
              by khelane
              Hello
              I have a big problem and that is that in some cases when repairing active pfc power supplies I cannot work with a test lamp. I can only get help with 5 volts standby and for starting and starting I have to work without a lamp and this way there is a possibility of parts exploding and other parts being added.
              Sometimes with a multimeter test the problems can be reduced to some extent, but I had several cases that had to be tested on and online and recently two varistors exploded. They had terrible resistance because the power supplies were over 800 watts.
              Is there a way...
              06-03-2025, 01:00 AM
            • chronic519
              Mats / mods: detected and repaired GPU fault. Cant seem to test after!
              by chronic519
              Hello.

              GPU came in, green lines. Spent lots of time using to get the Mats / mods drive working (found on youtube).
              Found issue with a RAM block
              Replaced, green lines gone.
              Trying to test again, assuming getting the false positive. Originally had over 1K on a single bank. Now getting tosses low between banks.
              Used a good card to test and same results low errors 32+.

              I am just search for some form of command to do a full test on the GPU.
              I just ran the mats command with my good GPU and passed after roughly 40 min.
              The repaired one, ran...
              05-20-2025, 07:56 PM
            • alltvrepairs
              Lg TCon test pins for screen test
              by alltvrepairs
              Hi,
              i have a 65 Panasonic TX-65HX710E using vestel 17MB170 main and Lg tcon.

              Few drops of water fell probably near COF and have no display. Tried removing tabs but no.part of display present as if tcon fuse open. However 12v is present and tcon can be felt warm enough that supplies are present. Backlight and sound ok.

              Anyone knows if this TCon 6870c-0805A has any special test pins for rgb test?

              Appreciate your help....
              2 Photos
              06-13-2025, 06:33 AM
            • Loading...
            • No more items.
            Working...