HP w2007 white screen problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pcjiet
    Member
    • Dec 2010
    • 13

    #21
    Re: HP w2007 white screen problem

    Originally posted by pcjiet
    I replaced those 3 caps, they are 100uF 16v each, but the multimeter read the same voltage 6.3 v. What could it be? or may be this is the correct voltage?
    sorry, the caps are 1000uF 16v not 100uF

    Comment

    • momaka
      master hoarder
      • May 2008
      • 12164
      • Bulgaria

      #22
      Re: HP w2007 white screen problem

      Originally posted by jetadm123
      If one of the caps is shorted, how did you determine the value for the replacement? Most of the SMD ceramic caps are unmarked. Did you just use the datasheet for the AAT1164C as a reference?
      No, unfortunately, I wasn't able to determine the value of the shorted ceramic cap, so I just replaced it with one of the same dimensions that I cannibalized off of a dead video card. I know that's not exactly the best approach about fixing things, but I figured putting in any ceramic cap in there should be better than leaving the spot unpopulated. I did this with two monitors, one of which I've tested for a couple of days and it's been working fine.

      My guess is that you can use the AAT1164C datasheet (if you understand it). There is a section on page 16 of the datasheet that talks about the output capacitor, but unfortunately I'm not that advanced in electronics to understand it. However, the datasheet does give a typical application circuit on page 14, which calls for a total output capacitance of 47uF (C3) when the main boosted output voltage (Vout1) is 13.3v @ 300mA, and the inductor is 6.8uH. I'll speculate that as long as you stay somewhat close to this capacitance, that circuit should work. Since there are 4 ceramic caps on the main boosted voltage rail of your monitor, that gives you about 13uF per cap more or less. So look for a10-15uF multi-layer ceramic cap with the same dimensions.

      Of course don't change those ceramic caps unless you've found that one of them is shorted.
      Last edited by momaka; 12-29-2010, 10:23 PM.

      Comment

      • jetadm123
        Badcaps Legend
        • Feb 2010
        • 2169

        #23
        Re: HP w2007 white screen problem

        Originally posted by momaka
        No, unfortunately, I wasn't able to determine the value of the shorted ceramic cap, so I just replaced it with one of the same dimensions that I cannibalized off of a dead video card. I know that's not exactly the best approach about fixing things, but I figured putting in any ceramic cap in there should be better than leaving the spot unpopulated. I did this with two monitors, one of which I've tested for a couple of days and it's been working fine.

        My guess is that you can use the AAT1164C datasheet (if you understand it). There is a section on page 16 of the datasheet that talks about the output capacitor, but unfortunately I'm not that advanced in electronics to understand it. However, the datasheet does give a typical application circuit on page 14, which calls for a total output capacitance of 47uF (C3) when the main boosted output voltage (Vout1) is 13.3v @ 300mA, and the inductor is 6.8uH. I'll speculate that as long as you stay somewhat close to this capacitance, that circuit should work. Since there are 4 ceramic caps on the main boosted voltage rail of your monitor, that gives you about 13uF per cap more or less. So look for a10-15uF multi-layer ceramic cap with the same dimensions.

        Of course don't change those ceramic caps unless you've found that one of them is shorted.

        Thanks for the explanation. It's about all you can do since there are no schematics and the components are either unmarked or have a factory code on them.

        Comment

        Related Topics

        Collapse

        • ahmarzo
          Asus la-7322p white screen problem
          by ahmarzo
          My asus laptop motherboard la-7322p has white screen. Have tried new screen but same problem.lcd vdd is 1.8v when i removed the mosfet an short 3vs with lcdvdd white screen is solved but no data on screen...
          07-15-2022, 07:52 AM
        • domu
          Viewsonic VS16217 strange problem - white flickering screen on power up
          by domu
          As per subject, on power up display shows no image, but white
          flickering screen. Strangely, it only happen after power was lost
          when it was on. After power returns - white screen only, but if
          disconnect power for 12-24 hrs, and connect then again monitor
          works normally.

          Any clues how to go about it would be greatly appreciated.
          07-18-2023, 04:57 AM
        • mmccomputer
          problem with replacing lcd screen
          by mmccomputer
          I have an HP model : 14-cf0011nf and I want to change its display screen (it has an original 14" full HD TN 30 pins panel) which works without problem but I want to put another screen with an IPS panel, the problem is that I tried several screens but there is no display except with the original screen, I never had this problem before I changed hundreds without problems but this PC is not 'accepted than its original screen
          otherwise on the motherboard it displays edp and I don't know, do the panels I tried only work with the LVDS protocol?
          If anyone has any information on the subject...
          12-15-2024, 03:44 PM
        • jimjoe123
          LCD TV Green/Pink screen problem
          by jimjoe123
          I have a Dick Smith 37" LCD TV, Model GE6804. I am using it as PC extended monitor only.

          Problem is while watching tv, I hear a semi loud click(like a electrical breaker tripping due to overload, just sound like it but no actual electrical overload), then screen is covered with green or pink. I can still see the original picture image but overlayed by green or pink. See attached images. Pink.jpg is what I see, and Normal.jpg is before green or pink screen, What I captured was pink screen, but about 80% of time it's green and 20% of time it's pink.

          Then each time...
          02-23-2020, 01:29 AM
        • howardc64
          A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
          by howardc64
          Problem

          This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
          08-04-2024, 10:36 PM
        • Loading...
        • No more items.
        Working...