onkyo ht-r590

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • harleyman58
    Senior Member
    • Feb 2016
    • 89
    • usa

    #1

    onkyo ht-r590

    ok I have a ht-r590 and a ht-r990 both have the same problem no audio. the radio will not work, or the headphones. the video works. all the voltages check good. does the hdmi board control all the audio for the entire receiver? I cant find anything wrong. the schematics are already posted in my ht-r990 post just a few threads down ,the schematics are the same for both receivers.

    thank you kenny
  • ngvuanh
    Member
    • Jul 2013
    • 36
    • USA

    #2
    Re: onkyo ht-r590

    How about pure direct?

    Comment

    • harleyman58
      Senior Member
      • Feb 2016
      • 89
      • usa

      #3
      Re: onkyo ht-r590 hdmi board

      ok I found out that the hdmi board on the ht-r590 does control all the sound on the unit. if I heat the dts chip the sound comes back to life for a few minutes. I am going to try to resolder the chip to see if that will work.

      Comment

      • mmartell
        Badcaps Legend
        • Oct 2013
        • 3189
        • Canada

        #4
        Re: onkyo ht-r590

        I heard the problem was the ic itself, something akin to the nVidia fiasco from several years ago. But as you know sometimes the truth is hard to come by. Keep us posted on the reflow.

        Comment

        • harleyman58
          Senior Member
          • Feb 2016
          • 89
          • usa

          #5
          Re: onkyo ht-r590

          reflow did not work.

          Comment

          • Terryfictv
            Senior Member
            • Mar 2011
            • 124
            • USA

            #6
            Re: onkyo ht-r590

            Sometimes replacing the SMD capacitors ("top hats") AND re flow will work....for a while.

            Comment

            • harleyman58
              Senior Member
              • Feb 2016
              • 89
              • usa

              #7
              Re: onkyo ht-r590

              I replaced the caps already

              Comment

              Related Topics

              Collapse

              • FrancescoV
                Onkyo HT-R390 no sound output, video output ok
                by FrancescoV
                Good morning everyone,
                I'm trying to repair an onkyo ht-r390 that has no sound output, despite the volume being at maximum, the rest seems to work; the video output signal (coming from an hdmi input) is present, but the audio is absent. Similar situation if I send an audio signal from any input I have no output.

                The firmware reported is the following:
                M:1.00/11107BLP
                D:?.??/????????
                O:1.00/11107AL

                The DSP firmware given the question marks seems corrupt.

                On the BCHDM-0678 - 25140678 - QPWBCHDM0678A0 board the chip that usually seems...
                05-11-2025, 02:59 AM
              • zahi
                DSP dump BIN files for ONKYO TX-NR5009
                by zahi
                Hello everyone, I need DSP dump BIN files for ONKYO TX-NR5009, TX-NR3009, Integra DTR-80.3, PR-SC5509, DHC-80.3, DTR-70.3, I think also 5007 is the same, or other...
                I have replaced the DSP chip, still not working.
                Can you share please?​
                04-25-2025, 04:32 PM
              • roman-hartwig
                Onkyo TX-NR828 - popping sound every 5 min
                by roman-hartwig
                Object: Onkyo TX-NR828
                Problem: Popping noises in the right surround channel every ~5min
                Service manual: available

                After I was able to bring my beloved Onkyo back to life (total failure of the power amplifiers) and it has now been doing its job for some time without any problems, it is now ailing with a new problem. It still works fully, but after about 5min it "pops" in the right surround speaker for about 0.5 sec very loud (100% volume). I am almost scared to death - sounded like a battery exploding or something. It sounds like something is discharging - a...
                07-29-2023, 08:08 AM
              • bios321
                onkyo CR-725
                by bios321
                Hello
                I restart an old topic Onkyo CR-725 board NCDG-8932, if someone can tell me the value of q941, c941, r941 and d941. thanks
                02-09-2025, 03:10 AM
              • Tom_x
                Onkyo HT-R390 DSP dump
                by Tom_x
                Hi

                I need DSP dump for Onkyo HT-R390.
                DSP board: BCHDM-0678
                DSP firmware corrupted, i need dump for Q282 spi chip (25q16) or dump from similar model with same dsp board

                thx
                Tom
                01-11-2025, 03:57 AM
              • Loading...
              • No more items.
              Working...