Omnitronic TUNA-NET Internet Radio - M1088 Module - any information or software?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • DriversScrew
    Member
    • Dec 2021
    • 28
    • Germany
    #1

    Omnitronic TUNA-NET Internet Radio - M1088 Module - any information or software?

    I've got an Omnitronic TUNA-NET internet radio with an all in one module built around an esp32. The module must be a M1088 from ALD Ltd.
    The device shows only a white display screen pulsing every second. Seems to have some kind of boot issue. All voltages and the pcb thermal signatures look good.
    Any information about the M1088 module, schematics or firmware would be helpful.
    Attached Files
    Tags: None
    • DriversScrew
      Member
      • Dec 2021
      • 28
      • Germany
      #2
      Hooked up a FTDI interface to RJ11 connector and got some unreadable output every second. Looks like boot looping to me.
      Perhaps not easy to solve without a working firmware file...

        Comment

        Previous template Next

        Related Topics

        Collapse
        • shelby5041
          clock radio / radio lifespan?
          by shelby5041
          hi
          ive got a modern digital clock radio approx 15yrs old

          my question is how long can a clock radio or a simple radio last ss farcas operating hours?

          since elec components have limited hour lifecspan i would imagine the radio or clock radio would eventually fail.

          the reason i ask is because i have my clock radio on radio function 24/7 for the past 7 years and its still working fine....i leave the radio on ..never turn off past 7years...thats approx 60000 hours

          it uses very little power just a few watts i would imagine that may have something...
          09-14-2024, 03:30 AM
        • speggio91
          820-00165 pulsing and stuck at S5
          by speggio91
          Hello everyone!

          I have this board that got slightly water damanged and it is stuck at S5 state. It pulses once every 5 seconds.
          When connected the magsafe 2 to the bench psu, the current goes from 0.02A to 0.10A when is pulsing.

          When using the genuine magsafe 2 charger, the light turn on and it became green and then amber. The fan is not spinning.
          When I tried the SMC bypass mode, the fan spins a quarter every 5 seconds and the pulsing is still present every time the fan spin.

          The pulses are present in the CPU Vcore rails on L7320 and L7310....
          11-25-2023, 11:25 AM
        • BOSCHNJAK
          by BOSCHNJAK
          ABOUT ME INTRODUCTION FILE

          2          024 BEV, BIH, SARAJEVO START PROJECT: ELECTRIC VEHICLE TOYOTA 4 RUNNER CONVERSION http://www.bev.ba/TOYOTA4RUNNER/index.html
          2023 BEV, BIH, SARAJEVO START PROJECT: SECRETS AND MANUFACTURING PLANS (AS MY REPLICA) OF THE LIBERTY ENGINE 2.0.
          2022 BEV, PROJECT ?
          2021 BEV, PROJECT ?
          2020 BEV,BiH, Sarajevo: PROJECT IS: HOW TO SWITCH OFF PERMANENT MAGNET FIELD and HOW TO SWITCH ON PERMANENT MAGNET FIELD?
          2019 BEV, Croatia, Ston:, Broce: PROJECT - PROJEKT ELEKTRIČNI GLISER http://www.bev.ba/ELEKTRICNIVANBRODSKIMOTOR/indexHR.htm...
          12-28-2023, 02:09 PM
        • UserXP
          Vintage SONY Digital Clock Radio ICF-C12W no audio
          by UserXP
          Dear all,

          I have this old radio clock by Sony from the early 80s, I guess. The clock display works, but is dim, the function board appears to be OK - but the radio unit shows no signs of life. It doesn't produce a single noise, crack or anything from either FM or AM band. It's like it doesn't even power up.
          i opened the radio and it is full of some TRACON gray capacitors. They only have their negative strip printed, voltage and capacitace markings - no series, no temperature marking, nothing else.
          My question is, do you know of this brand of capacitors and how bad are...
          07-21-2025, 08:35 AM
        • Omron
          Kenwood KDC 3051G Car Radio permanently stuck in Demo Mode please help
          by Omron
          Hello Guys! I have trouble with my car radio Kenwood KDC 3051G I hope someone more knowledgeable can help me, I tried everything in my power that I stumbled upon online.

          My radio is permanently in demo mode, it says Press Volume Knot Cancel Demo and when I press it nothing happens.

          - Tried to unplug radio and plug it back in into power,

          - Tried to reset radio by holding reset button key for 5,10,30 seconds while in power and without power, plugging it back in, it wouldn't work.

          - Tried to hold 3,6 while turning it back on and then pressing 1,2...
          05-23-2024, 01:27 PM
        • Loading...
        • No more items.
        Working...