Re: Oven broiler stuck on!!!!
how much power is the oven heater?
that relay is rated 10A inductive load - that's 2500w
how much power is the oven heater?
that relay is rated 10A inductive load - that's 2500w
-
-
Re: Oven broiler stuck on!!!!
how long did it last before going faulty ?Comment
-
-
Re: Oven broiler stuck on!!!!
so the relays lasted 18 years ?Comment
-
Re: Oven broiler stuck on!!!!
Yup oven was bought new in winter of 2000.Last edited by junktv; 07-31-2018, 05:48 AM.Comment
-
Re: Oven broiler stuck on!!!!
so that's a new relay?
is it exactly the same as the original?Comment
-
Re: Oven broiler stuck on!!!!
No it's the original relays. All I did last time was fixed the dry joints put it back together and it's been working since last december. I think I did clean that contact with some sand paper then also.
This time I am going to order new relays though since I seen it was stuck. I actually pulled the relay apart when I removed the back.Last edited by junktv; 07-31-2018, 06:21 AM.Comment
-
Re: Oven broiler stuck on!!!!
new ones should last 18 years .Comment
-
Re: Oven broiler stuck on!!!!
Trying to decide If I want to go ahead and replace those caps.
Nichicon says the PR is replaced with PS. Pr is a standard for switching with a impedance of .053 with 1100 ripple. PS is a low impedance for switching .058 with a 1600 ripple. Would the FM's be better for the PR? I see one FM says general and one FM says low impedance which seems odd.
https://www.mouser.com/ProductDetail...6hqa%252bt0%3d
https://www.mouser.com/ProductDetail...KHKNEftJEVA%3d
The kl says standard low leakage and looks like it's still available.
No clue on the other 2.Comment
-
Re: Oven broiler stuck on!!!!
FM is low, use the PS if your that concerned.
the ps has a better ripple capability too.Comment
-
Re: Oven broiler stuck on!!!!
I'm sorry it was FC that momaka had mentioned. Higher ripple and hour rated but lower impedance at .034 than the PS.Last edited by junktv; 07-31-2018, 11:56 AM.Comment
-
Re: Oven broiler stuck on!!!!
probably fine to use.Comment
-
Re: Oven broiler stuck on!!!!
Just a heads up newark seems to be having a big sale on a lot of nichicon PW caps pennies on the dollar.
https://www.newark.com/c/passive-com...ange=pw-seriesLast edited by junktv; 07-31-2018, 01:05 PM.Comment
-
Re: Oven broiler stuck on!!!!
Well I save a buck buying from newark and closer so would get it sooner but would have to use a FC vs PS(PR replacement) and find a replacement for the KL. Mouser has them so will probably just order from there.Last edited by junktv; 07-31-2018, 01:45 PM.Comment
-
Re: Oven broiler stuck on!!!!
PS and PW will both do fine, as will Panasonic FC. In fact, I think Panny FC is rated for automotive applications, so they'll be okay with all the heat. Not that FR or FM are any worse, but they are getting close to ultra-low ESR and have aqueous electrolyte, IIRC. Meanwhile, PW, PS, and FC have the older non-aquous electrolyte that's proven to last over the years in harsh conditions.Comment
-
Re: Oven broiler stuck on!!!!
The newark PW sale I was just letting you guys know about since yall have helped me a bunch. I figured since some of you do this for a living you could stock up cheap.
Sorry I meant PR not FR. I don't know this stuff like you guys and I get confused with all the series. lol Will probably just order from mouser since they have PS and kl in stock and the PS closer on impedance. Shame the 2 surge brand caps don't have any info on type.Last edited by junktv; 07-31-2018, 01:58 PM.Comment
-
Re: Oven broiler stuck on!!!!
These KL's have 2 models. Only difference I see is the tollerence 10% vs 20%.
https://www.mouser.com/Passive-Compo...yx4aw3Z1z0vhz5
Well most others are 20% so went with that one.Last edited by junktv; 07-31-2018, 03:47 PM.Comment
-
Re: Oven broiler stuck on!!!!
Just noticed something the old kl says KL(K) and new one says KL(M). is there any difference?Comment
-
Re: Oven broiler stuck on!!!!
That is the tolerance code (M = 20%, K = 10%).Comment
-
Re: Oven broiler stuck on!!!!
Ah ok Thank you.
I wonder if there will be a problem using the 20% one instead of the 10%. Or if I should put the old one back in.Last edited by junktv; 08-03-2018, 08:20 PM.Comment
-
Hi guys i've got an Hp laptop Zbook 17 g5 Stuck on Hp protected by hp sure start screen.
I have tried almost every bios available on various platforms about this laptop but the problem is still the same.
I even successfully build my own bios using the one from the Hp website but the problem the laptop still getting stuck there.
Even if i try to press Esc key nothing happens. I tried f10 it doesn't go to bios still stuck there i just saw entering setup menu on the bottom left corner of the
screen that's it and stuck there. I left it until the following day and i still...09-02-2025, 01:51 PM -
I had a lot of trouble with the WiFi connection from my router inside of the house into a ( new ) metal garage I had to run a 150 ft cat6 patch cord so the WIFI connection would be strong enough for the WiFi connection on the garage door opener would work correctly ( my son has a work out area in the garage as well and he was having to put his phone near the door to be able to stream music ) ( so I was going to eventually put WiFi out there anyway )
This garage door opener WiFi is very touchy if you lose the power it does not remember the password for the router which is weird or... -
OK. I got the rocker switch figured out thanks to the good advice on this forum.
Now I need to figure out the correct wire to go to the switch from the broiler element and from the oven element.
This is a Whirlpool RDE3340 electric range.
The common wire on the switch appears to have a high temperature insulating material. I am guessing that both the wire to the broiler and the wire to the oven elements also need relatively high temperature insulation. What do I need to look for? The broiler is rated at about 2400 watts.
Where may I find parts... -
There is a motherboard Gigabyte H610M S2H V2 (DDR5), I can't find boardview
Help to identify the element, marking on the element - C31PH. It stands next to the USB 3.0 and it looks like it is ESD Protect chip. We need a datasheet to this element. Maybe someone has already identified such an element. Help please.
... -
Hey....
Board as written in description was stuck at VGA LED. common Problem wit these type of bords.... tried all the "standard stuff" like resettin... reseatin.... found out the LED Controller MCU1 = IT8295FN-56A geting burning hot under the last PCI Slot.. now i desoldered it cause there were only 18 ohms at the caps arround.... another aorus x470 in working condition with similar part and nearly same layout had arround 280 ohms...
my question is: why doesnt the board start know without this chip.... worked myself through the boardview but i can´t understand...
Comment