Water Damaged Diseqc Sat Switch

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Per Hansson
    Super Moderator
    • Jul 2005
    • 5895
    • Sweden

    #21
    Re: Water Damaged Diseqc Sat Switch

    Originally posted by stj
    diseq switches should be on the back of the dish - or even slung under the lnb-arm.
    and should be sealed the same way you seal the lnb - i use GEL-LOCKS when i work on them - much better than amalgamating tape and you can remove & refit them!
    Mine was installed under the roof, I made the mount myself.
    Of course the painter washing it with high powered jet wasn't in my planning lol
    Attached Files
    "The one who says it cannot be done should never interrupt the one who is doing it."

    Comment

    • CapLeaker
      Leaking Member
      • Dec 2014
      • 7985
      • Canada

      #22
      Re: Water Damaged Diseqc Sat Switch

      Originally posted by fzabkar
      ISTM that if the micro were bad, then more than 1 port could be switched on. The fact that only the first port is switched on would suggest that the micro has powered up in its default, programmed state. It now needs a DRX signal from the receiver before it can switch to a different LNB. I would be checking the circuit between the DRX input and the receiver.
      I've seen many broken switches, but none of them had all ports on at the same time. Now why that is, I never investigated, because I have a pile of them. I just change them out. With 10 sat dishes outside, 3 of them on C band, I need a lot of switching done.
      Last edited by CapLeaker; 07-21-2016, 05:27 AM.

      Comment

      • stj
        Great Sage 齊天大聖
        • Dec 2009
        • 30931
        • Albion

        #23
        Re: Water Damaged Diseqc Sat Switch

        you need a H2H or a jack - it would be cheaper!

        Comment

        • DJ_MIX
          Senior Member
          • May 2005
          • 118

          #24
          Re: Water Damaged Diseqc Sat Switch

          Originally posted by CapLeaker
          if it isn't switching between the ports and only port 1 works, then I think that the Tiny13V is at fault. Either it isn't getting any power, or the IC is bad. If it is bad, you are SOL unless you can program another one.
          I'm also think it's tiny13v and it appears it has to be programmed.

          So I file this as trash can, or keep it for parts.

          I appreciate everyone's help and effort it this.

          Comment

          • fzabkar
            Badcaps Veteran
            • Mar 2009
            • 772
            • Australia

            #25
            Re: Water Damaged Diseqc Sat Switch

            @DJ_MIX, if you could upload a detailed photo of the reverse side of the PCB, perhaps I could trace the circuit for you. I'm also using your thread as a learning exercise. :-)

            Comment

            Related Topics

            Collapse

            • RetroComputingGrotto
              Water Damaged Toshiba 48L1435DB
              by RetroComputingGrotto
              I have a water damaged Toshiba TV that was hanging nicely on the wall then over the summer we had a new multi-million pound boiler system put in and right where this TV was hanging is a nice new pair of water pipes for the radiators...

              The TV hasnt been used for a fair few months but it was needed again the other day and needless to say, it didn't power on or show any signs of life (no standby LED etc). After checking the fuse in the plug (and that the socket it was plugged in to worked) I decided to get up some step ladders to take a closer look and low and behold! It looks like...
              10-07-2024, 08:23 AM
            • Document Archive
              Acer Switch Switch V 10 SW5-017P Hybrid (2-in-1) V 10 Specification for Upgrade or Repair
              by Document Archive
              This specification for the Acer Switch Switch V 10 SW5-017P Hybrid (2-in-1) can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the Switch V 10 SW5-017P boardview and Switch V 10 SW5-017P schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification,...
              09-06-2024, 05:30 AM
            • rzsn
              water damaged G513I
              by rzsn
              Hello friends, so I have got a "water damaged" (or cola/beer/coffe .. something dark and sticky) G513I system - which has the board and schematics from this thread. After cleaning up all the visible sticky residue with water and detergent (thankfully mostly on the top/keyboard side), I have a partial success. IPA was of no use for cleaning this.

              Using a bench power supply on the DCIN jack (as it seems that the PSU keying pin is not wired at all - series resistor R6003 is not populated), and using a shoring wire for the power button (either pin 5 on CN251 keyboard, or one...
              12-22-2024, 09:02 PM
            • estabilito
              Dell Latitude E5590(La-f411p) water damaged
              by estabilito
              Hi,
              I have water damaged Dell Latitude E5590 around charging ic.
              Laptop was dead but i replaced some components like capacitors, resistors, resoldered charger(intersil 9538h) but traces under PQ904 dual mosfet(AOE6936) was burnt.
              I rebuilt traces and both mosfets(PQ904 and PQ905) and after all this work laptop started turning on.
              I dont have battery so i want to be sure if laptop behaviour is normal before buying.
              On PL902 i have weird voltage around 5Volts, on battery socket voltage looks normal - 13.5v.
              Is this voltage on pl902 normal?...
              03-08-2025, 06:22 PM
            • abajor
              A2141 820-01700 Water Damage L8504 Damaged, U3100/U3200 power cycles UB300/UB400 5V .25A
              by abajor
              Like title says A2141 came in with Water Damage, customer desperately wants the data.

              The actual water ingress doesn't appear too bad it sat for a day but was very dusty internally. I have no idea why L8504 was arced there is no apparent moisture there or around the LVDS cable; however, the LVDS to screen screw studs had popped off at some point and somebody tried securing it with kapton tape.

              I had to create a micron wire pad jumper to reconnect the south side of the L8504 since the primary pad was blasted down to the vias.

              That said after cleaning up the...
              12-21-2024, 07:16 PM
            • Loading...
            • No more items.
            Working...