Questions about PicKit 3.

Collapse
X
Collapse
 
  • Page of 5
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 5 template Next
  • stj
    replied
    Re: Questions about PicKit 3.

    got a pk3 here.
    the pk3 uses a socket-strip 2.54mm pitch 6pin

    i make cables using pinstrips.

    btw, the design is open and the chinese have nice clones.
    http://www.ebay.com/itm/141774464184

    this one comes with cables and a programming board!
    (my next upgrade )

      Leave a comment:

    • Spork Schivago
      started a topic Questions about PicKit 3.

      Questions about PicKit 3.

      Hello,

      I'm interested in buying a PicKit 3 programmer, like the one located here:

      http://www.microchip.com/Development...paign=PICkit+3

      I've modified a circuit that has a pre-progammed PIC (16F628A) and added an ICSP 6-pin header. I noticed though, that the kit only comes with the PicKit 3 and a USB cable. Does anyone know where I can get the 6-pin cable at? Also, I've seen talk about an RJ-11 connector. Is that just for debugging in-circuit or am I supposed to be using RJ-11 connectors instead of ICSP 6-pin male headers? If so, that'd really suck.

      Finally, I see talk of some special header for in-circuit debugging. It appears to be a circuit board. But there's a few different "header" packages. How useful is in-circuit debugging and do I really need to purchase one of these special "headers"?

      Here's a link to a PDF that talks about the various headers. https://cdn.badcaps-static.com/pdfs/...9062dabff9.pdf

      This is all new to me so I apologize if some of my questions sound a bit naive. Thank you.
      Tags: None
      Previous 1 2 3 4 5 template Next

      Related Topics

      Collapse
      • tommy1331
        hp envy 15t k000 debugging
        by tommy1331
        Hi, I'm quite new to this, I am trying to debug a faulty motherboard (DAY31AMB6C0). There was a fault in the DC input circuit with a faulty TVS diode after the first MOSFET shorting the VAD rail to ground. I was able to clear that fault by removing the diode and now the input section seems to be working correctly and I get the V3PCU power rail.

        But trying to start the board still fails, I put some RAM in it and shorted the power button to start it up but it only blinks the power LED in the DC jack assembly 3 times. Maybe the AC detect circuit is broken? Or is this more likely to be...
        04-28-2025, 08:12 AM
      • Ihandyrepair
        ID smd 6pin chip - GM2 for electric scooter display
        by Ihandyrepair
        Hi

        working on a not turning on Wheelspeed WS1 scooter.
        diagnosed - issue is the display/power button

        on the board, with the multimeter I noticed there is a short to ground. as the red wire has 0 ohm to ground.
        with infrared camera, this chip (photo circled) would heat up if I push power button on.
        but I can't find any replacement or online info of this chip.
        on the chip you can see it has a label GM2H, I have another good working display with the same chip but it has label GM2C

        could anyone help me id this chip and guide me to...
        05-08-2024, 06:59 PM
      • seppde
        Benq Zowie XL2540K / Power board failure / 6Pin-SOP-Chip identification
        by seppde
        Hello everyone,
        I've got a Benq power board of a XL2540K monitor which suffered from a power cut and is since defective / won't turn on. It's got obvious defects, some blown resistors, some burning around the drain pin of a MOSFET...
        ... and some 6-pin IC I struggle identifying, that is driving said MOSFET.
        The IC is labeled as IC601, so someone with a circuit schematic could probably identify it really quick, unfortunately I can't find the schematics.
        In other power boards of Benq for which I did find the schematics, IC601 is an 8-pin NCP1200 PWM controller - I suppose...
        2 Photos
        02-09-2024, 05:19 AM
      • belalmondeo
        Car code scanner OBD1 adapter enquiry
        by belalmondeo
        Hello everyone there
        If You do remember me then I am Belal who posted an issue of his J2534 pass-thru Multi-Diag 2015 OBD II device a while ago and aside from my thanks that show my gratitude to all of those who have given me help with my issue I just wanted to go straight into my question which is whether using the OBD II to OBD I adapter to diagnose an older model vehicle like a GM 12 adapter safe enough and not gonna cause any catastrophic failure to my device and if it still can perform scanning with no issues?
        there's a link for the adapter: https://ebay.to/2UCWDDx
        ...
        04-05-2019, 06:00 PM
      • thrinrot
        Zotac GTX 960 2GB- 6pin PCIE Power not recognized
        by thrinrot
        Hi all!
        A friend of mine brought me a defective Zotac GTX 960 with a failing power detection.
        Even though the 6 pin PCIe power cable is plugged in, the card says "Plugin PCIe power cable and reboot".

        Since I have no schematics it is hard to find out the NVVDD_PGOOD trace.

        I checked if the Controller (NCP81174) sends a Power good signal and the signal VR_RDY at pin 3 is high. So I assume the controller is not sending a bad signal (?).

        I appreciate your help! :-)
        09-25-2021, 12:29 PM
      • Loading...
      • No more items.
      Working...