Hello everyone there 
If You do remember me then I am Belal who posted an issue of his J2534 pass-thru Multi-Diag 2015 OBD II device a while ago and aside from my thanks that show my gratitude to all of those who have given me help with my issue I just wanted to go straight into my question which is whether using the OBD II to OBD I adapter to diagnose an older model vehicle like a GM 12 adapter safe enough and not gonna cause any catastrophic failure to my device and if it still can perform scanning with no issues?
there's a link for the adapter: https://ebay.to/2UCWDDx
it worths mentioning that I was using this device to run scans on a wide variety of vehicle makes including (Skoda - Chevrolet - VW - Renault - Peugeot - Chery (general OBD) - Nissan (general OBD) - Toyota) and much more, but it's actually works like charm with VAG vehicles and has the capability of coding/adapting functions despite being a clone, but I used to face issues with a few number of cars that I've tried to perform scan to with the protocol ISO 15765-4 CAN (11 bit ID,500 Kbaud), these vehicles were ( 2011-2016 Renault Fluence - 2000-2006 Mitsubishi Lancer - Chery QQ6)
and I just wanted to get a way around it, since this device is actually J2534 Pass-thru based then it has the capability of performing perogrammming to a number of makes with each manufacturer specific software Like (Toyota techstream - GM TIS200 - JLR - Honda HDS) but it's a little restricted and might be compatible with specific versions of these pieces of software I mentioned above, it also can be reworked to be much stable and fast during the work !
please check for the software in the link above if You're interested !
the software (MDO I-2017 sP1-sP2-sP3) : https://wishes2.com/AuRjt
2011 VCI : https://ebay.to/2NoCf2Z
Pickit 2-3 with ZIF adapter (debugging tool) for performing a hex file dump to the chip (clone) : https://ebay.to/2E7IEeH
Genuine Pickit 3 : https://ebay.to/2BQeHzD
Genuine Pickit 2 : https://ebay.to/2tBIA1R
Soic 8 clip : https://ebay.to/2H0Yw5Y
Video for using the Pickit 2 software for the hex file dump : https://www.youtube.com/watch?v=7jcJGwNoXCE
Video for using the Pickit 3 (IMPLAB) software (using a universal adapter from Ebay) : https://www.youtube.com/watch?v=hSkmPyhopRk
IMPLAB (Pickit 3 software) : https://wishes2.com/xmfpq
Pickit 2 V.2.61 (Pickit 2 software) : https://wishes2.com/T3aY
HEX file : https://wishes2.com/CJzh
Keyupdate : https://wishes2.com/2eBjB
Drivers : https://wishes2.com/FEn73
Best Regards !
If You do remember me then I am Belal who posted an issue of his J2534 pass-thru Multi-Diag 2015 OBD II device a while ago and aside from my thanks that show my gratitude to all of those who have given me help with my issue I just wanted to go straight into my question which is whether using the OBD II to OBD I adapter to diagnose an older model vehicle like a GM 12 adapter safe enough and not gonna cause any catastrophic failure to my device and if it still can perform scanning with no issues?
there's a link for the adapter: https://ebay.to/2UCWDDx
it worths mentioning that I was using this device to run scans on a wide variety of vehicle makes including (Skoda - Chevrolet - VW - Renault - Peugeot - Chery (general OBD) - Nissan (general OBD) - Toyota) and much more, but it's actually works like charm with VAG vehicles and has the capability of coding/adapting functions despite being a clone, but I used to face issues with a few number of cars that I've tried to perform scan to with the protocol ISO 15765-4 CAN (11 bit ID,500 Kbaud), these vehicles were ( 2011-2016 Renault Fluence - 2000-2006 Mitsubishi Lancer - Chery QQ6)
and I just wanted to get a way around it, since this device is actually J2534 Pass-thru based then it has the capability of performing perogrammming to a number of makes with each manufacturer specific software Like (Toyota techstream - GM TIS200 - JLR - Honda HDS) but it's a little restricted and might be compatible with specific versions of these pieces of software I mentioned above, it also can be reworked to be much stable and fast during the work !
please check for the software in the link above if You're interested !
the software (MDO I-2017 sP1-sP2-sP3) : https://wishes2.com/AuRjt
2011 VCI : https://ebay.to/2NoCf2Z
Pickit 2-3 with ZIF adapter (debugging tool) for performing a hex file dump to the chip (clone) : https://ebay.to/2E7IEeH
Genuine Pickit 3 : https://ebay.to/2BQeHzD
Genuine Pickit 2 : https://ebay.to/2tBIA1R
Soic 8 clip : https://ebay.to/2H0Yw5Y
Video for using the Pickit 2 software for the hex file dump : https://www.youtube.com/watch?v=7jcJGwNoXCE
Video for using the Pickit 3 (IMPLAB) software (using a universal adapter from Ebay) : https://www.youtube.com/watch?v=hSkmPyhopRk
IMPLAB (Pickit 3 software) : https://wishes2.com/xmfpq
Pickit 2 V.2.61 (Pickit 2 software) : https://wishes2.com/T3aY
HEX file : https://wishes2.com/CJzh
Keyupdate : https://wishes2.com/2eBjB
Drivers : https://wishes2.com/FEn73
Best Regards !