Announcement

Collapse
No announcement yet.

MAXENT MX26X3 L2614XW02L no standby light, no power on

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    MAXENT MX26X3 L2614XW02L no standby light, no power on

    i have a MAXENT MX26X3 L2614XW02L here that wont turn on.
    i can see power going from the plug, to the power board, and even some power coming out into the mainboard but pressing the power button does nothing
    and the standby red light does not come on.

    i took voltage measurements of all the cable pins on the mainboard and made a graphic. im still new at this so i wont try to guess at what it might be. at first i thought it must be the power board since no standby light comes on but then i see the mainboard IS getting some power so now im kinda confused...could the switch be broken? does the switch send a signal to the mainboard, and then the mainboard sends a signal to the power supply to turn on from 5v to 12v?

    anyway if anyone can look at the volts im getting on this mainboard and give me a hint, i'd be greatly appreciative.

    thanks!
    Don't fear the repair...

    #2
    Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

    whats the power and main board numbers can you post pictures up as they might be a board we reconise thanks.

    Comment


      #3
      Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

      dangit..i thought i had uploaded the pics on the last post but i guess not.

      ok here they are...
      ive got the voltages on the mainboard measured. working on the other boards. will post those in the next one
      Attached Files
      Don't fear the repair...

      Comment


        #4
        Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

        heres all the boards
        Attached Files
        Don't fear the repair...

        Comment


          #5
          Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

          ok heres the voltages on the power board and the little mini board next to it
          Attached Files
          Don't fear the repair...

          Comment


            #6
            Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

            i get 4.85v to the power switch on the button board... but to be honest i dont really know whats supposed to happen on the button board when the power button is pressed... how is that signal relayed to the motherboard? does a voltage change?
            Don't fear the repair...

            Comment


              #7
              Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

              pics of the button board
              Attached Files
              Don't fear the repair...

              Comment


                #8
                Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                numbers on the mainboard:
                QPWB11497-1G
                Don't fear the repair...

                Comment


                  #9
                  Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                  numbers on powerboard:
                  RUNTP1048-1
                  05050422339
                  Don't fear the repair...

                  Comment


                    #10
                    Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                    numbers on button board:
                    11438-16-2
                    Don't fear the repair...

                    Comment


                      #11
                      Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                      theres 4.9v to all the buttons... 0v to the green LED 3.92 to one side of the red led and 5.03 to the other side thers some resistors and things on this board and a lot of them have voltages on them too around 5v... so it really seems like the button board is getting everything it needs...
                      Don't fear the repair...

                      Comment


                        #12
                        Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                        voltage pics
                        Attached Files
                        Don't fear the repair...

                        Comment


                          #13
                          Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                          hmm on the last board i was working on (vizio vo37L) there were voltage regulators all over the main board but here there are none... not sure what else to test...ill leave it at this for now and hope someone can give me some ideas. thanks again!
                          Don't fear the repair...

                          Comment


                            #14
                            Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                            ...anyone got any ideas??
                            Don't fear the repair...

                            Comment


                              #15
                              Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                              Do you have the remote? If you do have voltage at the swithes, then it means you must have 5VSTBY on one of the pin for the connector between the power supply board and the main board. See any fuses on the main board?
                              I cannot see any 3-pin voltage regulator ICs either. What does the bottom side look like? There must be more SMD parts on the bottom side.
                              Last edited by budm; 05-19-2014, 11:24 PM.
                              Never stop learning
                              Basic LCD TV and Monitor troubleshooting guides.
                              http://www.badcaps.net/forum/showthr...956#post305956

                              Voltage Regulator (LDO) testing:
                              http://www.badcaps.net/forum/showthr...999#post300999

                              Inverter testing using old CFL:
                              http://www.badcaps.net/forum/showthr...er+testing+cfl

                              Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                              http://s807.photobucket.com/user/budm/library/

                              TV Factory reset codes listing:
                              http://www.badcaps.net/forum/showthread.php?t=24809

                              Comment


                                #16
                                Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                                i do not have the remote. i do not see any fuse on the mainboard. i will take the board off and upload a picture of the underside...
                                Don't fear the repair...

                                Comment


                                  #17
                                  Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                                  ok heres whats on the underside of the mainboard
                                  Attached Files
                                  Don't fear the repair...

                                  Comment


                                    #18
                                    Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                                    its gonna be hard for me to test the voltages because with all the wires plugged in i cant get at the back of the board...
                                    Don't fear the repair...

                                    Comment


                                      #19
                                      Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                                      actually it wasnt as hard as i thought...heres the voltages on the regulators...
                                      now to look them up!
                                      Attached Files
                                      Don't fear the repair...

                                      Comment


                                        #20
                                        Re: MAXENT MX26X3 L2614XW02L no standby light, no power on

                                        hmm i need help figuring out how to lookup datasheets on these things...
                                        i type in 5 cal 17-18 and i get datasheets for the 1117... are there some things im just supposed to know about these numbers on these chips? what does 5cal mean?
                                        Don't fear the repair...

                                        Comment

                                        Working...
                                        X