winbond W74M12JWSSIQ
Hi, anyone know the appropriate programmer to read/write to this part? Thanks in advance, Gaxxter
-
-
Re: winbond W74M12JWSSIQ
Have you tried the CH341A? It´s pretty common and I think it works for every chip out there. I haven´t found yours specifically, but I guess that it´s a standard SOP 8, so you shouldn´t have any problem.
What device is it from? -
Re: winbond W74M12JWSSIQ
https://www.winbond.com/hq/product/c...artNo=W74M12JW
nothing cheap is gonna do it.
good luck!
whats it from and have you got the data to put in it?Comment
-
Re: winbond W74M12JWSSIQ
Good day all!
i have RT809F and it detect as a w25q128 1.8v, read and write with no problem.Comment
-
I used for W74M12JW, CH341A + Adapter 1.8V + software NeoProgrammer.
chip is defined as W25Q128FW [1.8V]Comment
-
Winbond W74M12JWSSIQ
I need to know if the ch341a works on this chip. Could you help me or should I buy a 1.7 volt adapter?Comment
-
Just replaced this chip with 25Q128JWSQ on a Lenovo Ideapad and works like charme.Comment
-
Hi,
I've managed to take an image dump in BIN format of my Dell Latitude 5420, which had a Winbond 25R256JV chip installed.
I used an RT809F programmer to obtain the BIN, using the supplied iFix RT809F programmer application (latest version being 20220830).
The programmer automatically found the settings to read the chip but selected the Winbond W25Q256FV instead (my actual model isn't available on the listing within the software). The image came out fine - I did this multiple times to clarify the data being read was the same each time.
... -
Hi everyone,
help me please
I have an HL-DT-ST BD-RE GGW-H20N with ROM version: XA02.
When I tried to burn a 25GB Blu-ray disc using ImgBurn, I got an error.
I will share all the details with you, including the disc information.
...Code:HL-DT-ST BD-RE GGW-H20N XA02 (ATA) Current Profile: BD-R Disc Information: Status: Empty State of Last Session: Empty Erasable: No Free Sectors: 12,219,392 Free Space: 25,025,314,816 bytes Free Time: 2715:27:17 (MM:SS:FF) Next
-
i recently bought a new wd re4 2tb with 2014 datecodes. when i got around to testing it tho in victoria hd tester, the write speed was very slow at 14 mb/s with a 256 sector transfer size. when i increased the transfer size to 1024 sectors, the write speed increased slightly to 44 mb/s. read speeds and sector verify speeds were fine and at normal speeds.
so i just ass-u-med the drive's poor performance was due to it being an advanced format drive and i was using it on winxp. when i tried cloning my system disk to this wd re4 2tb drive and writing to it in linux, the write speed... -
Hello,
Here I have the mentioned tablet with motherboard s6000-mb-h401. The tablet won't turn on, no display, charging normally. I manage to connect to UART port and got this output when I try to start it:
...Code:[PWRAP] pwrap_init_preloader [PWRAP] pwrap_init [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5 [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=1 rdata=5AA5 [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=2 rdata=5AA5 [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=3 rdata=5AA5 [PMIC_WRAP]wrap_init pass,the return
-
Hi to all, I'm facing a problem writing to an MX25L25673G SOIC-16 bios chip (part of an HP EliteOne 1000 G2 27") with a Willem programmer 5.0B (with software PCB98D12c4).
I know my programmer is old and I've planned to buy a new one but it worked until now with every eeprom I've faced in different devices, this is the first time that is giving me this kind of problem and I need to urgently solve it because I've already changed the fried southbridge and cleaned its ME fw, so I need to finish the last step of the repair.
This Willem supports some 256Mbit eeprom, I can choose between...
Comment