This chassis does not run YouTube.
https://drive.google.com/drive/folde...hx?usp=sharing
arizanotlari
Senior Member
Last Activity: Yesterday, 06:34 AM
Joined: 11-05-2014
Location: Diyarbakir
-
Check blon voltage not pwron....Leave a comment:
-
Leave a comment:
-
Red light blinking and goes off when power button is pressed.
This is what it should be. check backlights.Leave a comment:
-
Re: I need 6870C-0511A Tcon Dump
It should have been empty anyway. So the problem is solved.Leave a comment:
-
I need 6870C-0511A Tcon Dump
Tv: Lg 65UB980V
Panel : LC650EQF-FGF1
Tcon : 6870C-0511A
Hi.
i need tcon dump (u450) of 6870c-0511a. The eprom I have is empty. Maybe it should be empty but I wanted to ask you to be sure. -
Re: Telefunken 55" Model TLEDD-55FHDA (bad picture)
Didn't you know this? Some of the 51-pin lvds have 3, some 4, and some 5 supply pins. These (in my opinion) set the standard of LVDS. If you examine the schematics of TVs of different brands (Samsung, LG, etc.), you can see the differences.Leave a comment:
-
Re: Telefunken 55" Model TLEDD-55FHDA (bad picture)
According to LG standards, the 44th leg is used for AGP, but in some TCONs this leg is used, while in others it is used as gnd.
Unfortunately, AGP cannot be activated because this leg is grounded in the tcon in question....Last edited by arizanotlari; 11-12-2023, 05:20 AM.Leave a comment:
-
Re: Telefunken 55" Model TLEDD-55FHDA (bad picture)
For Fhd : Apply 3.3V to pin-44.
51 50 49 48 is panel vcc
7. Specific pin No. #44 is used for “No signal detection” of system signal interface.
It should be GND for NSB(No Signal Black) during the system interface signal is not.
If this pin is “H”, LCD Module displays AGP(Auto Generation Pattern).Leave a comment:
-
Re: Luxor TV board input board change but picture upside down
Read the 7th message...Leave a comment:
-
Re: Luxor TV board input board change but picture upside down
https://disk.yandex.com/d/-YdVftsdIffr6wLeave a comment:
-
Leave a comment:
-
Re: Vestel 17IPS12
Dont touch primary side. psu working good. check c113 and replace led strips.Last edited by arizanotlari; 10-18-2023, 03:37 AM.Leave a comment:
-
Leave a comment:
-
Re: LED Panel information
ask to google
https://cdn.badcaps-static.com/pdfs/...30c27440ae.pdf
https://cdn.badcaps-static.com/pdfs/...bce05e021f.pdfLeave a comment:
-
Re: Gogen TV 17MB25-3 DUMP - bad chip 19"
try this....Leave a comment:
-
Re: Adapting a samsung panel to Vestel 17MB211
We need picture of chassis.Leave a comment:
-
Re: Adapting a samsung panel to Vestel 17MB211
VES315WNDA-2d-n12 = CN16
Samsung HD = CN15
CN14 should not be used this chassisLeave a comment:
-
Re: Adapting a samsung panel to Vestel 17MB211
actually this problem looks like a lvds socket problem. I tried the panel software on the Samsung panel and it worked without any problems.Leave a comment:
-
Re: Adapting a samsung panel to Vestel 17MB211
Samsung HD Panel file : https://disk.yandex.com.tr/d/672hb9tqJMwcZwLeave a comment:
No activity results to display
Leave a comment: