After a power outage, my lg plasma tv fails to start. When i try to start up the TV, clicking sound comes from psu and the Red light desapears. After a minute the red light is back on. No sound no image nothing.I checked all voltages on the secondary of power suplly and only 5 volts stby is correct. I checked some parts like power mosfets, diodes, zeners. fuses, resistor, etc.On the first side of psu 300v on big caps is on. If you can help i would appreciated. Thanks!
-
-
Re: LG 50pq3000
use the "Search" feature in this forum and enter your model number, there are lots of threads that might be helpful. -
Re: LG 50pq3000
I checked all the posts already. Nothing helpfulComment
-
Re: LG 50pq3000
Try disconnecting VS supply from the Y-sus and Z-sus and see if the voltage comes up on the power supply side. If there is a short on either board the power supply will go into over current shutdown.Last edited by R_J; 03-15-2021, 07:59 PM.Comment
-
Re: LG 50pq3000
I tested the psu with the motherboard only and the problem its the same no voltages.I changed the motherboard with another and nothing happens I suspect the psu because of the AC power outage for a few second. I am electronic tech. here in my country but my knowledge its not good with plasma tv's. I understand the logic of all the bords but i dont have the experience, because i fixed plasma's only 2 or 3 times. Thanks.Comment
-
Re: LG 50pq3000
The power supply should auto start on AC power only, with all other cables disconnected from it (YSUS and motherboard), VS, VA and all other voltages should come up, if they don't, power supply is faulty.Comment
-
Re: LG 50pq3000
Ac voltages 220v , bridge +300v DC on the first part of psu its ok. Second Part cables to motherboard only 5 volt stby is stable and cables VS, VA to YSUS have no volts. I believe PSU without the mainboard is not start to fix all the other voltages. I understand from the begining that the problem is the PSU and check almost all important parts on it, with no luck. So is someone who have the same problem with me or any idea how to fix it?
Thanks.Comment
-
Re: LG 50pq3000
You should have 5V on AUTO_GND pin on the connector that goes to mainboard, with all cables disconnected except AC.
No relays clicking?
Post a photo of your power supply front and back sides.Comment
-
Re: LG 50pq3000
Check that the fuse F801 is okComment
-
Re: LG 50pq3000
Biruslapio please check symptom on my first post. 5 volt is on, relay clicking, Red light desapear, no sound no image, and after a minute Red light is back again.Without mainboard relays not clicking.
RJ all fuses are OK.Comment
-
Re: LG 50pq3000
You should be able to check the power supply on the bench with just ac mains connected. You can use a 1k resistor between STBY5V and RL_ON, this should give you at least the 12V. If this works you can turn on the VS with another resistor between STBY5V and VS_ON, this should give you the VS voltage, but wiyhout a load it might come up and drop back down.Comment
-
Re: LG 50pq3000
Watch my video, sounds like the MB has BGA solder issues and is failing intermittently. Force a power up first to check.Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: LG 50pq3000
The mainboard is changed with another one with no effect. I try tomorow to start the psu with the resistors and see what happens. Thanks for your advices.Comment
-
Re: LG 50pq3000
The results from the bypass with resistors is the same. No dc power on the mainboard and VA, VS connectors. I believe that the big IC with 28 pins is not working properlyComment
-
Re: LG 50pq3000
[ATTACH]232725[/ATTACH]Comment
-
Re: LG 50pq3000
It looks like, but hard to read the number off your photo precisely, that it's an MC80F0704 micro
https://datasheetspdf.com/pdf-file/6...OR/MC80F0704/1Willing to help but I'm no expert.Comment
-
Re: LG 50pq3000
Its the mc80f0708-09fd.Comment
-
Re: LG 50pq3000
What voltage do you have on Pin 5. Does it match what's given in the data sheet?Willing to help but I'm no expert.Comment
-
Re: LG 50pq3000
I think is 5.1 volt after a fast search for voltages on the IC but i will check tomorrow for sure.Comment
-
Re: LG 50pq3000
Check if the main DC voltage on F801 changes from the 300 volts to around 385 volts when you connect STBY5V and RL_ON with the 1k. You can use one of the heat sinks in the primary for hot ground. Also do you here the relay click when you do this test?
Thanks for the picture, I was looking at a different power supply before.Last edited by R_J; 03-19-2021, 06:45 PM.Comment
-
Hi everyone, over the past few months i have taken a deep dive into motherboard diagnostics and I love the challenge. Currently im trying to learn all about the signals that travel around the motherboard, such as frequencies, enable signals High and Low logic states etc. And i have been learning to read and using the Schematics for this board that i requested here on Badcaps forum, from a few months ago, this is such a great place for these.
I’ve been working on a GA-970A-DS3 (rev. 1.0) that does not post. This motherboard has been my main learning board. I would like share...11-23-2023, 11:02 PM -
This is A2289, board 820-01987-A. It came in with the screen not working. We could not see any image on the screen, so we ruled out a backlight issue and instead replaced the panel. The display now comes up, but no backlight.
I didn't see any signs of liquid damage, but there was some odd looking spots around U8400. F8400 has voltage on either side of it, and I have 5v present on R8444 and R8445. I did not have 3.2v at R8442 so I figured U8400 was bad, and I replaced it. After replacement, a brief probe to R8442 showed 3.2v so I assumed I had fixed the device. After reassembly however,... -
Hello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM -
Hello,
I am strouglling with this TV.
Model: Le40C550J1WXXC and inverter and power suplly BN-4400340B
It boots up normally, but no backligth.
I have check the PFC resistors from 814 to 818 and resolder all of them, I get 380Vdc on the 100uf 450v caps.
I have checked DP803 / ZDM806 / QM801 / ZI802 / QP801 802 / QI801 803
Replaced IPC801 fan7530
All solder joints were checked and also the electrolitics for capacitance and ESR.
I am lost, can someone help me with this issue.
Best regards
Nezoca... -
LG 50PQ3000
Opened this TV and it looked like someone had emptied a hoover bag over all the boards. I cleaned all the boards front and back and noticed the main fuse on the power board had failed. I couldn't see any bad caps so I replaced the fuse and the TV worked with no problems, all voltages were good.
Comment