Re: Blaupunkt 50" LED TV firmware please
They sent another version but neither have managed to revive this tv.
Both files are named AllUpgrade_6308rtec.bin, one for a 50-148Z & one for 50-149Z.
On the reverse of my Tv back panel it says 50-149z-gb but on the reverse of the main board it has 50-148z so I found a serial number to obtain the fw for a 50-148z tv to try, but no luck!
I must say, I found UMC very helpful and quick to respond.
-
-
-
Re: Blaupunkt 50" LED TV firmware please
Wow, fast response, file received already.
Unfortunately after it does the update the tv just power cycles (around 1 min) by itself with an unresponsive blue screen after the 'Blaupunkt' splash screen.
Remote control and keypad has no effect.Last edited by notallbad; 04-03-2020, 04:48 AM.Leave a comment:
-
Re: Blaupunkt 50" LED TV firmware please
Thanks. Have made contact with them today so shall see if they are able to help.Leave a comment:
-
Re: Blaupunkt 50" LED TV firmware please
have you tried this web site and see if they will supply it too you
http://www.umc-uk.co.uk/feedbackform.phpLeave a comment:
-
Re: Blaupunkt 50" LED TV firmware please
Theres no obvious uart connection on this board, i.e no DB port, ex-link or even any markings etc... Guess it would be necessary to remove the heatsink to find the Mstar chip ref markings to look up on datasheet, if its even possible.Leave a comment:
-
Re: Blaupunkt 50" LED TV firmware please
With a working main board is there any way of retrieving the nand flash to then transfer across to the faulty board?
Not quite sure what the 'Erase all and gen Nand' option does but think I need a passcode to select that option as the 'Format USB' option does not do anything.
Service menu entered via 'Menu', then '1147'.
ThanksLast edited by notallbad; 04-01-2020, 05:39 PM.Leave a comment:
-
Re: Blaupunkt 50" LED TV firmware please
More photosAttached FilesLeave a comment:
-
-
Re: Blaupunkt 50" LED TV firmware please
Main boardAttached FilesLeave a comment:
-
-
Blaupunkt 50" LED TV firmware please
Make : Blaupunkt
Model : 50/149Z-GB-5B2-FGKU-UK
Main board : T.MS6308.801 (V500HJ1-PE8)
Panel : LC.4N301.001
Made a stupid mistake in service menu, now the tv won't power up. So need to somehow reset the tv / firmware.
Thanks.
-
Hello to everyone ,
This is my first post here, and i would like to share with you a small story in case you can help me.
Docker Type-C Gen 2 - Model 40AS. Was given to me by a friend for free ,but with the problem that you cannot use the video output ports.
All ports work , USB , Ethernet, Type C ... but HDMI + Display Port don't work
I searched on reddit and google for problem similar to that, and a LOT of people had fixed this problem by updating the firmware. So i tried , i searched and found 1.1.13 utility and 1.1.20 utility that can help... -
Hi,
I have an Anker SoundCore 2 (A3105) that I saved from the trash (well, I guess there's a reason why it was supposed to go into the trash...). The problem is that it always turns off after a few seconds (sometimes it stays on a bit longer, between 30 and 60 seconds, but it still turns off). The power light turns on and the bluetooth light starts blinking, but both abruptly turn off again. The "turn off sound" is still played after the lights turn off. Sometimes, it also loops the on-off cycle several times without me pressing any buttons. If I connect an AUX cable, music...08-11-2025, 02:14 PM -
Hi guys.
I've got a Ubiquiti US-8-150W POE switch which has issues with updating the firmware.
Turned out to be a bad EEPROM chip. It would read the firmware and work as normal, but failed to write new firmware to it.
So I took off the chip and read on EEPROM and saved it. Wrote to old chip and failed to write
Got New chip and writes good.
THE PROBLEM...
It fails to fully load the firmware, POE lights fail to work during g firmware test during load. I'm suspecting bad EEPROM Read.
Does anyone have a Good Firmware I can have?... -
Hello Badcaps Community,
I purchased a preowned AOC monitor that is not working and out of warranty. It was sold as not working. I am looking for guidance on self-repair. In particular, I am after the firmware for the monitor. At the end, I have included monitor model information and links to pics and vids of the issue.
The problem is that it will not display a picture on any of its inputs. And the on-screen menu does not appear. The power button works properly. It powers on with the remote as well. But the on-screen menu does not appear, even when not connected to any... -
Hi,
I have OriginPC EON 15SL, however, my laptop starts and shutsdown after 1-2 second. Keyboard leds are coming on then fans spinning then it shutsdown and not turning back on unless I plug out the power cable and plug it in. I had issues with bricked BIOS then I flashed BIOS I got from the vendor to the SPI chip and still it didn’t worked because my EC firmware was newer than the BIOS I have flashed. So I wanted to try flashing the EC chip with the correct firmware that matches with the BIOS also from the vendor and it worked everything was well, and then stupid me wanted to unlock some...
Leave a comment: