Sony Bravia KDL-40W5500 - 14 blinks problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • vinceroger69
    Badcaps Legend
    • Mar 2012
    • 6714
    • uk

    #21
    Re: Sony Bravia KDL-40W5500 - 14 blinks problem

    did you do the test in post 15?

    Comment

    • jetadm123
      Badcaps Legend
      • Feb 2010
      • 2169

      #22
      Re: Sony Bravia KDL-40W5500 - 14 blinks problem

      From what you provided the main cap is putting out 389VDC, which means the PFC circuit is on. You also say the back_light_on command, which comes from the main board, is 0V. At this point, I suggest you test the voltages at connector CN6150. If those voltages check good, then you could have a bad main board.
      Last edited by jetadm123; 03-04-2018, 03:05 PM.

      Comment

      • jetadm123
        Badcaps Legend
        • Feb 2010
        • 2169

        #23
        Re: Sony Bravia KDL-40W5500 - 14 blinks problem

        Re-reading your chart in post 16, it looks like your INV_ERROR pin has been triggered, which indicates a problem in the inverter section. Suspect this is what's preventing the BACKLIGHT_LIGHT_ON command from being sent. Check the resistor as budm/vinceroger69 suggested.
        Last edited by jetadm123; 03-04-2018, 03:22 PM.

        Comment

        • neilc6
          Badcaps Legend
          • Nov 2015
          • 1550
          • Canada

          #24
          Re: Sony Bravia KDL-40W5500 - 14 blinks problem

          Maybe this thread applies https://www.badcaps.net/forum/showthread.php?t=66995

          Comment

          • turbosl2
            New Member
            • Jun 2018
            • 8
            • USA

            #25
            Re: Sony Bravia KDL-40W5500 - 14 blinks problem

            What was your fix. I am having something similar but a little more complex of an issue on a similar TV

            Comment

            • can1363
              New Member
              • Dec 2022
              • 1
              • Türkiye

              #26
              Re: Sony Bravia KDL-40W5500 - 14 blinks problem

              Originally posted by alpersen
              Tried update, formatted FAT32 (was already FAT32, reformatted neverthless), plugged in then turned on TV. After 2 secs flash drive leds blinked a couple of times, then off for 2-3 secs, then blinked couple of times then stopeed. And approximately 4-5 secs TV led started infamous 14 red blinks and turned off.
              Alper merhaba, benzer bir sorunu bende yaşıyorum şuan. Konu hakkında çözüme varabilmiş miydin? Teşekkürler. Can ERDOĞAN (Turkish)

              Hello Alper, I'm having a similar problem right now. Were you able to come to a solution on the issue? Thank you. (English)

              Comment

              Related Topics

              Collapse

              • swrb898
                Sony KD-70X690E Bravia; Bad TCON? Bad panel?
                by swrb898
                What's wrong with my TV: the TCON, the panel, or something else? I'm stuck.

                Problem:

                Last week, my Sony KD-70X690E 70" stopped displaying a picture. The TV powers on, and the back lights power on. However, the TV doesn't seem to boot up. I say this because the SONY splash-screen logo does not display, nor does any picture display, nor can I invoke a menu by pressing "Menu" on the remote. Other than back-light bleed, the screen is black.

                My troubleshooting got me this far:

                With the left-hand TCON to bottom-board ribbon cable...
                12-28-2021, 08:12 PM
              • iglitare
                Sony KD-75XF9005 grey Picture but Sound. TCON or panel?
                by iglitare
                Hi,

                i want to repair a Sony KD-75XF9005 TV that initially only showed a grey picture.
                Backlight seems to work, Sound (Setup menu after reset) works.
                If i dissconnect the left FFC cable from TCON to panel i have half a screen on the right. If left cable is connected always only the grey screen.
                Interchanged the cables, its always only the right side that is working. Always grey if left side is connected.
                With my small knowledge i would think at least the cables are good.

                Can this happen because of a bad tcon board?
                Or is it always a bad/shorted...
                09-04-2025, 07:13 AM
              • PopsCaps
                Sony Bravia KDL-40V2500 that will not power on
                by PopsCaps
                I have a Sony Bravia KDL-40V2500 that will not power on. The indicator flashes red 3 times.
                I do not hear any sound and I cannot see any backlight.
                I have tried disconnecting every cable on each board one at a time to see if anything changes.
                The only change is when I disconnect AC-DET cable on the Power Supply board or on the other end if I unplug the CN7009 connection on the B-Board and try to power on the TV the indicator will stay on solid green until I power off.
                My friend ordered another used power supply board but it is also doing the red indicator flash 3 times...
                03-25-2025, 11:23 AM
              • kca
                LG 82UN8570AUD ~ TCON or PANEL?
                by kca
                Hello all ~

                Hope this finds you well. This LG 82UN8570AUD (April 2021 model) 4K UHD television has full audio capabilities but video is compromised / problematic.

                When I picked up this large LG tv it had a full black screen upon startup. Previous owner said it just went black one day. No popping sound or anything else of note.

                I got the display to work by taping off several traces of the right-hand side ribbon cable on the TCON that leads from TCON to PANEL. However, despite dozens and dozens of attempts to find the right combination / range of traces taped...
                08-31-2025, 06:38 AM
              • thelankanguy
                Sony KD-55X9000F TCON Issue
                by thelankanguy
                The TV shows a black screen with no image.
                TCON ribbon connectors were disconnected individually for image and there was no half image even.
                Later both ribbons were disconnected and TCON voltages were tested.
                12V, 3.3V, 1.8V were seen present but VONE signal reads 0V.
                There is also a short to ground in this circled inductor.
                Is this a TCON issue or something else ?...
                12-13-2024, 12:27 AM
              • Loading...
              • No more items.
              Working...