Need SMD partnumber

PowerAmpFreak

Badcaps Veteran

Join Date: Feb 2010

Posts: 982

Country: Sweden
#1

Need SMD partnumber

02-23-2017, 07:44 AM

Hi all
I need to know what SMD component marked "MP1" is. SOT-23 (3 pin)
It looks like a voltage regulator or powerswitch and seems to power +5V to various things on an LG mainboard.
Tags: None
dskall

Badcaps Legend

Join Date: Oct 2016

Posts: 2905

Country: usa
#2

02-23-2017, 11:54 AM

Re: Need SMD partnumber

This is my best guess https://cdn.badcaps-static.com/pdfs/...34c5daaca9.pdf look at figure 5 P-channel MOSFET

I assume no responsibility for any stupid suggestions I might post.
Comment

Previous template Next

Identify pwm sot23-6 marked 6315

by tibd

Hello
Anybody came across this tiny sot23-6 PWM and knows where to find data sheet or yet better pin-pin compatible chop?...
- Channel: Troubleshooting Power Supplies and Power Supply Design
06-29-2023, 05:53 AM
HP 2311 display, 3.3v regulator fried, need help to replace

by disorder

hello,

i have a hp display 2311 to repair, totaly dead
on the board, il have 2 capacitor 470µf that are dead and the 3.3v regulator : ax6630-33
i have no such regulator, can i replace this one with a mic5209-33 (3.3v outpout regulator too) ?

thank you
- Channel: Troubleshooting Computer Displays
07-27-2025, 04:34 AM
uP0109: 2A Ultra Low Dropout Linear Regulator equivalent substitute

by bilux

Hello everyone,
I want to find a replacement for uP0109 8pins, and i found this parts:

uP0109 is "2A Ultra Low Dropout Linear Regulator"
RT9199 is "Cost-Effective, 2A Peak Sink/Source Bus Termination Regulator"
FP6137C is "2A BUS TERMINATION REGULATOR"

can replace uP0109 by RT9199 or FP6137C ?
- Channel: General Electronics Technical Discussion
11-01-2024, 12:00 PM
Reader PocketBook InkPad 3 – identification of a black component marked 'CT' on the microUSB line

by Maniackk

Hello,

Device: PocketBook InkPad 3
Mainboard: XRZ_E091_PB740-VTTOA-V1.1 / 2017-10-12

I'm replacing the broken microUSB connector on this e-reader, and during inspection after desoldering, I noticed a loose black SMD component marked "CT". One of them was torn off along with the pad, while the other one (marked in the photo) is still in place.

I would appreciate help identifying this component.

Measuring the loose component with a multimeter gives 5.84 MΩ in both directions, while the one still on the board shows no measurable...

2 Photos
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
05-16-2025, 08:53 AM
diy - voltage injection possiblity with voltage and ampere regulator - possiblity ?

by playit

hello ,for diy voltage injector for short killer/finder -- is it possible to use something like this - LM317 DC Linear Regulator, DC-DC 4.5~40V Turn 1.2~37V, Step Down Power Module, Adjustable

and ampere controller along (to make it zero amps ) with some addons(transistors diodes etc.) for it -- and use some 5v adaptor or 3.3v volt rail of my smps power supply as input and finally get 1v and zero amps for injecting voltage to find out short circuit component ? ..
for source input -- can we use 3.3 -4 volt 18550 battery ?( i have some of those ) and then adding ampere regulator...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
02-26-2025, 05:39 AM
Loading...
No more items.

Need SMD partnumber

Need SMD partnumber

Comment

Related Topics