HP 2311 display, 3.3v regulator fried, need help to replace

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • disorder
    Senior Member
    • Sep 2015
    • 156
    • france
    #1

    HP 2311 display, 3.3v regulator fried, need help to replace

    hello,

    i have a hp display 2311 to repair, totaly dead
    on the board, il have 2 capacitor 470µf that are dead and the 3.3v regulator : ax6630-33
    i have no such regulator, can i replace this one with a mic5209-33 (3.3v outpout regulator too) ?

    thank you
    Tags: None
    • lotas
      Badcaps Legend
      • Jan 2016
      • 4595
      • Russia
      #2

      It won't work according to the current, 1.5A versus 0.5A.

        Comment

        • disorder
          Senior Member
          • Sep 2015
          • 156
          • france
          #3
          ok thank you

            Comment

            Previous template Next

            Related Topics

            Collapse
            • tamerelapute
              [LA-J891P] Warm cpu on 19v rail injection, is it fried ?
              by tamerelapute
              Hi,
              I'm learning electronics(already have some basics) by fixing a FH52M LA-J891P rev1B. It come from an acer nitro 5. The charger was defaulting upon pluging. The 19V rail resistance is 0ohm (I believe that caps screw my measurement). When i inject 5A, I get a rail tension of 1.3V, and 0.8V vcccore.
              Except the cpu, I cant feel anything getting warmer.
              I believe that it is normal, because the cpu is "eating" half the power I'm imputing.
              I dont know if the cpu is fried, because I did not remove the big capacitor on vcccore.
              I believe that if the cpu was fried,...
              07-08-2024, 03:28 PM
            • playit
              diy - voltage injection possiblity with voltage and ampere regulator - possiblity ?
              by playit
              hello ,for diy voltage injector for short killer/finder -- is it possible to use something like this - LM317 DC Linear Regulator, DC-DC 4.5~40V Turn 1.2~37V, Step Down Power Module, Adjustable

              and ampere controller along (to make it zero amps ) with some addons(transistors diodes etc.) for it -- and use some 5v adaptor or 3.3v volt rail of my smps power supply as input and finally get 1v and zero amps for injecting voltage to find out short circuit component ? ..
              for source input -- can we use 3.3 -4 volt 18550 battery ?( i have some of those ) and then adding ampere regulator...
              02-26-2025, 05:39 AM
            • Document Archive
              ISL95831HRTZ ISL95831HRTZ-T ISL95831IRTZ ISL95831IRTZ-T Voltage Regulator Datasheet
              by Document Archive
              3+1 Voltage Regulator for IMVP-7/VR12 CPUs

              Compliant with IMVP-7/VR12, the ISL95831 provides a complete solution for microprocessor and graphic processor
              core power supply. It provides two Voltage Regulators (VRs) with three integrated gate drivers. The first VR can be
              configured as 3-, 2- or 1-phase VR while the second output is 1- phase VR, providing maximum flexibility. The two VRs share the
              serial control bus to communicate with the CPU and achieve lower cost and smaller board area compared with the two chip approach.
              Based on Intersil's Robust Ripple Regulator...
              11-05-2024, 03:24 PM
            • artvandalai
              Help identifying voltage regulator on this concept 2 pm5 monitor pcb board?
              by artvandalai
              This Concept 2 rower pm5 monitor doesn't shut down. It keeps turning on and stays on after being turned off. I read on another forum by another user that replaced the same component to check the voltage regulator.
              The monitor should pull around 35mA when turned on and in shutdown it should drops to around 0.060mA. Any advice on finding the voltage regulator on this board to check if it needs to be replaced?

              ​
              3 Photos
              11-05-2024, 07:38 AM
            • Bonaventure Vigil
              What cable to connect from Power Supply Regulator
              by Bonaventure Vigil
              Hi everyone,
              I'm still newbie and want to start up the shop for motherboard repairing. Need help what cable to connect from psu variable or regulator to any motherboard that we repairing? Any cable names? Since i already order the power supply regulator. From that, i can check the current and voltage go inside motherboard.
              10-01-2024, 01:47 AM
            • Loading...
            • No more items.
            Working...