Eeprom dump thread!
Collapse
This is a sticky topic.
X
X
-
-
Re: Eeprom dump thread!
hello LOTAS,
I flashed the U10 and u12 eproms with the 17MB82-1A software (EN25q64; BIN ET en25q16; BIN) that you generously provided me and then I put the USB key with the vestel 17mb82-1A Recovery software USB program. When switching on the television, the LEDs of the television and of the USB key flashed quickly and at the same speed. A few minutes later the led of the USB key changed to fixed and the led of the television continued to flash more slowly and the TV still does not start. Do you have a solution for my problem.
Thank youhttps://www.badcaps.netComment
-
Re: Eeprom dump thread!
lg 24mt48df-pzAttached FilesComment
-
-
Re: Eeprom dump thread!
FhdComment
-
Re: Eeprom dump thread!
Looking for a dump from a LG 19LG3000 television or a Hitachi 19LD4550u they use the same main board and screen just use different remote controls
screen: M190A-L0A
Main Board: 715T3009-2 VER:A
Flash ic: U404 MXIC3205D 16pin
Attached is a 22LG3000 dump which works but reduced image on the whole of the screen, which is why I require the 19inch version.
So would appreciate anyone with a suitable 4mb dump from the TV.Attached FilesComment
-
Re: Eeprom dump thread!
Managed to find a youtube video which Italian guy had the files who kindly sent them to me this afternoon.
This is for the LG 19LG3000 which I have used in Hitachi 19LD4550U (as this model is quite rare). Bear in mind you will need to change the remote control if you have a Hitachi remote to a LG remote control.
screen: M190A-L0A
Main Board: 715T3009-2 VER:A
Flash ic: U404 MXIC3205D 16pin
The dump has resolved the issues with the TV ie remote control not responding and side control buttons not operational!Attached FilesComment
-
Hitachi 49hg6w69 i h
Hallo to everyone,
my TV set is booting twice, showing logo "inspire the next" and then goes to ST/BY. Not starting. (Happened after 1st use of Amazon Fire Stick).
LCD panel VES490QNEL-2D-U01 and board are VESTEL (17MB120).
I suppose i have a corrupted FW. It could be?
The question is, where to find the right one (maybe here?) and how to properly upload it on the nand flash (hopefully without desoldering the chip).
Thanks in advance for any suggestion.
LexComment
-
Comment
-
Comment
-
Re: Eeprom dump thread!
thanks for the input is the ic the top line of the chip?
as in mxic mx ? i guess board model would help as well, i was trying to copy other posts, but lots of these numbers and terms i am not too familiar with
thanks again !Comment
-
Comment
Related Topics
Collapse
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.
-
Channel: Troubleshooting Computer Displays
07-26-2025, 03:24 PM -
-
by (0)_(0)Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
by my2k2Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.-
Channel: Troubleshooting Audio Equipment
07-01-2024, 09:04 PM -
-
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work....-
Channel: BIOS Requests ONLY!
-
-
by Ancient1Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... - Loading...
- No more items.
Comment