V315B1-C01 TCON - AS15F Swap out - resistor values

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pic_whiz
    Member
    • Feb 2014
    • 36
    • United Kingdom

    #1

    V315B1-C01 TCON - AS15F Swap out - resistor values

    Hi All,

    I was just in the process of replacing the usual failed AS15F Gamma IC but inadvertently removed 8 of the SMD resistors that connect to the IC!

    The values of each resistor I have are:-

    6K
    1.3k
    752r
    752r
    430r
    388r
    160r
    140r

    Would someone be so helpful as to identify which resistor goes into which position on the attached photo marked 1-8 (If only I had a spare board to compare :-)

    Cheers,

    Matt
    Attached Files
  • dick_barton
    Badcaps Legend
    • Aug 2015
    • 6643
    • Wales

    #2
    Re: V315B1-C01 TCON - AS15F Swap out - resistor values

    It's hard work but if you can read it from the data sheet, google AS15F data sheet
    Last edited by dick_barton; 12-27-2016, 03:29 PM.
    Willing to help but I'm no expert.

    Comment

    • pic_whiz
      Member
      • Feb 2014
      • 36
      • United Kingdom

      #3
      Re: V315B1-C01 TCON - AS15F Swap out - resistor values

      Thanks Dick. I've already looked at all possible datasheets/diagrams but unable to find the same values located on any of them.

      Still hoping someone may have the same board to do a quick meter reading of their resistors.

      Cheers,

      Matt

      Comment

      • pic_whiz
        Member
        • Feb 2014
        • 36
        • United Kingdom

        #4
        Re: V315B1-C01 TCON - AS15F Swap out - resistor values

        Any more help guys? Still struggling to find the info..

        cheers,

        Matt

        Comment

        • vinceroger69
          Badcaps Legend
          • Mar 2012
          • 6714
          • uk

          #5
          Re: V315B1-C01 TCON - AS15F Swap out - resistor values

          ignore wrong thread sorry

          Comment

          • pic_whiz
            Member
            • Feb 2014
            • 36
            • United Kingdom

            #6
            Re: V315B1-C01 TCON - AS15F Swap out - resistor values

            bump!

            Comment

            • pic_whiz
              Member
              • Feb 2014
              • 36
              • United Kingdom

              #7
              Re: V315B1-C01 TCON - AS15F Swap out - resistor values

              Comment

              • Charudatta
                New Member
                • May 2017
                • 3
                • India

                #8
                Re: V315B1-C01 TCON - AS15F Swap out - resistor values

                Does any one have standby V315B01-C08 T-Con board . I need resistor values for 1-18 as in Picture. Some resistor are swiped by heatgun bi mistaken. IC chip is As15-HG NOT AS15- F. I have datasheet for AS15-HG but is it worth. Not clear from application data. Any on could help me please
                Attached Files

                Comment

                • dskall
                  Badcaps Legend
                  • Oct 2016
                  • 2905
                  • usa

                  #9
                  Re: V315B1-C01 TCON - AS15F Swap out - resistor values

                  I realize this is older post but may help someone with the V315B1-C01 per post 1
                  1=160r
                  2=6k
                  3=140r
                  4=388r
                  5=1.3k
                  6=430r
                  7=752r
                  8=752r
                  I assume no responsibility for any stupid suggestions I might post.

                  Comment

                  Related Topics

                  Collapse

                  • skdsp
                    Need help identifying resistor values near BIOS chip on ASUS Zephyrus G14 GA402XV
                    by skdsp
                    Hello,

                    I purchased a laptop that the previous user had tried to remove and replace a BIOS chip using a soldering iron not knowing that there is a ground pad under the 25R256JWEQ chip. In that process he damaged the BIOS chip and 3 of the resistors near the IO3, CLK, and IO0 pins. I have programmed a spare 25R256JWEQ chip using a CH341A programmer but not sure what values those resistors should be. If anyone has a boardview of this area and can provide those values that would be very useful for me.

                    Attached is the photo.

                    Thank you!
                    09-27-2025, 09:05 PM
                  • Kobok
                    Different (lower) resistor values on PCB?
                    by Kobok
                    Dear Alls,
                    For sure it id a stupid question, but help me to understand. I am in a Dell 2007WFP revitalizing project - searching reason why not starting. Some resistors needed to replaced is is obvious. When I have soldered some resistors the measured (with multimeter) values were sometimes rather different written on them. I supposed these are wrong units so I desoldered and made a checking measurement and voilá the values is the same is written on. This happens only in case of a few resistors, most have the same values (+/- 10%) are written on it. "strange" SMD resistors =>103...
                    09-19-2022, 07:30 AM
                  • PowellSkier
                    Cement resistor swap in Harman Kardon AVR
                    by PowellSkier
                    Would I be able to swap a 0.27 Ohm Kx2 5W resistor for a 0.22 Ohm Jx2 5W resistor in a Harman/Kardon AVR? Cement type.
                    06-04-2024, 06:41 PM
                  • jinu_j
                    Dell 2209WA - power supply - Fusible Resistor replacement
                    by jinu_j
                    Hi

                    I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.

                    1. FR950 - blown fusible resistor - 0.2 Ohm 1W
                    2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
                    3. R835 - Blown Resistor - 20KOhm SMD resistor
                    4. D930 - Shorted Schottkey Diode...
                    05-03-2025, 10:51 PM
                  • madushanka 1234
                    need to find RESISTOR values of mising LA-E831P
                    by madushanka 1234
                    need to find mising parts LA-E831P
                    need to find values of this marked resistors...
                    another shop mixed this marked 5 resistors...
                    please check 3rd photo
                    (rt3661b section/puz1)
                    thank you
                    02-17-2025, 07:26 AM
                  • Loading...
                  • No more items.
                  Working...